Hologic DISCOVERY A Скачать руководство пользователя страница 198

Страница: 198 / 274

Discovery QDR Series Technical Manual

5-32

5.8.2 Aperture Motor PCB

To remove and replace the Aperture Motor PCB (140-0068), refer to Figure 5-16 and
follow the procedure below:

1. Shut down the computer and then turn off the main circuit breaker on the foot end

pedestal.

2. Remove the 2 Phillips screws from the motor shaft bracket.

3. Move the aperture back far enough to expose the screws that hold the PCB

bracket.

4. Remove the 2 PCB bracket screws.

5. Unplug the cables and install the new PCB on the bracket.

6. Reverse the steps above to complete the installation of the new Aperture Motor

PCB assembly.

7. Turn on the Discovery power, boot the computer and login as Service.

8. Perform the “Aperture Calibration ” on page 4-9.

5.8.3 Aperture Position Belt

To remove and replace the Aperture Position Belt (255-0032), refer to Figure 5-16 below:

1. Shut down the computer and then turn off the main circuit breaker on the foot end

pedestal.

2. Loosen the 2 belt tension nuts and the belt clamping nut.

3. Remove and replace the belt (ensure the belt is under the pem stud).

4. Tension the belt moderately tight (remove slack), and tighten the belt tension

nuts.

5. Remove the 2 Phillips screws from the motor shaft bracket.

6. Rotate the belt pulley fully clockwise, then turn the pulley back 3/4 turn counter

clockwise (3/4 turn of the potentiometer pulley, not the idler pulley).

7. Move the aperture towards the potentiometer until it stops.

8. Tighten the belt clamping nut (do not over tighten).

9. Move the aperture back until the motor shaft bracket screw holes line up.

10. Install the 2 Phillips screws holding the motor shaft bracket.

11. Turn on the Discovery power, boot the computer and login as Service.

12. Perform “Aperture Calibration ” on page 4-9.

Содержание DISCOVERY A



















































































































































































































































































Результаты поиска

Содержание DISCOVERY A

Отзывы:

Похожие инструкции для DISCOVERY A

Бренды по названию

Популярные бренды

Hologic DISCOVERY A, Техническое руководство

Результаты поиска

Содержание DISCOVERY A

Отзывы:

Похожие инструкции для DISCOVERY A

Бренды по названию

Популярные бренды