INSTALLATION NOTES:
r
Pollux-13
©
Holm
2018
ARCHITECTURAL & LANDSCAPE LIGHTING
Typical Installation:
Installation Guidelines:
This product is intended to be installed in standard 4" (10 cm)
recessed retrofit or new-construction housings. Please refer
to documentation provided with housing for housing installation
information.
The rPollux-13 accepts 10- to 15-volt power only. Please ensure
a step-down transformer is providing power to the luminaire.
Installing the Luminaire
Figure A
– Connect the rPollux-13 luminaire to the down light
housing using the attached two-pole quick-connect.
Figure B
– Fully insert the luminaire body inside the housing. The
mounting tabs will engage with the inside of the housing holding
the luminaire in place.
To remove the luminaire from the housing,
pull firmly by hand in the downward direction. Disconnect the
quick-connect to service the luminaire.
Accessing the LED Board and Optics
Figure C
– Once the luminaire is removed from the housing, loosen
the setscrew and pull the trim firmly by hand to separate from the
luminaire body.
Figure D
– The LED optics are now accessible and can be changed
by hand. To remove the LED board, remove the screws and pull the
board by hand to separate from the luminaire body.
FIGURE A
FIGURE C
FIGURE D
WARNING – To reduce the risk of FIRE OR INJURY TO PERSON:
■
Turn off/unplug and allow to cool before replacing lamp/LEDs.
■
Lamp/LEDs gets HOT quickly. Contact only switch/plug when turning on.
■
Do not touch hot lens, guard, or enclosure.
■
Keep lamp/LEDs away from materials that may burn.
■
Do not touch the lamp/LEDs at any time. Use a soft cloth. Oil from skin may
damage lamp/LEDs.
■
Do not operate the luminaire fitting with a missing or damaged shield.
WARNING – Risk of Electric Shock
■
Install all luminaires 10 feet (3.05 m) or more from a pool, spa, or fountain.
■
A luminaire shall not use tungsten halogen lamps unless the luminaire is
marked for such lamps.
■
Supply connection and electrical components are located above ground level,
except for secondary cord that is suitable for wet locations.
LOW-VOLTAGE CABLE SHALL:
1. Be protected by routing in close proximity to the luminaire or fitting, or next to
a building structure.
2. Not be buried except for a maximum 6 inches (15.2 cm) in order to connect to
the main low voltage cable.
3. Have the length cut off so that it is connected to a connector within 6 inches
(15.2 cm) from a building structure, a luminaire, or fitting.
AVERTISSEMENT – Pour réduire le risque D’INCENDIE OU DE BLESSURE:
■
Éteignez/débranchez la lampe et laissez-la refroidir avant de la remplacer.
■
La lampe devient rapidement BRÛLANTE. Ne touchez que l’interrupteur/
la prise lors de la mise sous tension.
■
Ne touchez pas la lentille, le dispositif de sécurité ni le boîtier lorsqu’ils
sont chauds.
■
N’approchez pas la lampe de matériaux pouvant s’enflammer.
■
Ne touchez jamais la lampe. Utilisez un chiffon doux.
■
La graisse de la peau peut endommager la lampe.
■
N’utilisez pas le raccord du luminaire si le bouclier est absent ou endommagé.
AVERTISSEMENT – Risque d’électrocution
■
Installez tous les luminaires à 3,05 m (10 pieds) ou plus d’une piscine, d’un
spa ou d’une fontaine.
■
Les luminaires ne doivent pas utiliser de lampes tungstène-halogène à moins
que le luminaire soit prévu pour ce type de lampe.
■
Le raccordement au réseau électrique et les différents matériels électriques
doivent installés au-dessus du niveau du sol, exception faite pour les fils ou
réseaux secondaires qui conviennent aux lieux humides.
LE CÂBLE BASSE TENSION DEVRA:
1. Être protégé en le faisant passer à proximité du luminaire ou du raccord,
ou à côté d’une construction comme une maison ou une terrasse.
2. Ne pas être enterré sauf à un maximum de 15,2 cm (6 pouces) pour être
branché au câble basse tension principal.
3. Être raccourci de manière à être branché à un connecteur situé à moins de
15,2 cm (6 pouces) d’une construction, d’un luminaire ou d’un raccord.
Save These Instructions:
Conservez Soigneusement Ces Instructions:
DO NOT EXCEED 15 VOLTS IN THIS FIXTURE
The LEDs in this product function ideally when the incoming voltage is between
10–15 volts. Voltages outside of this range may damage the LEDs, shorten their
life, and cause unsatisfactory performance.
The use of improper voltage voids
the product warranty. Use only a UL 1838 approved power supply.
RISK OF FIRE WARNING: DO NOT USE LOW-VOLTAGE LUMINAIRES WITH
ANY STYLE OF TRANSFORMER THAT EXCEEDS 15 VOLTS ON THE SECONDARY.
These installation guidelines are to assist you in correctly installing luminaires and transformers. For any questions, call Holm Technical Support
at 877-848-9329 before proceeding. Follow all NEC guidelines and local electrical codes. For more information, visit: holmlighting.com
Recessed
4" (10 cm)
down light
housing
Connector
rPollux-13
luminaire
FIGURE B
Ceiling
Ceiling
Low-Voltage
Landscape Lighting
3YJ8
