FM-ONE
HOKUTO DENSHI
CO;LTD;
株式会社
25
Errors while writing
ターゲットカラノデンゲンガニュウリョクサレ
テイマセン
No power supply from target
Input VCC to 20pin of target I/F
ビットレートチョウセイシュウリョウノ００ガジ
ュシンデキマセン
No 00 replyed from target at rate adjust
Possibly, incorrect pin setting or too quick a
communication rate during boot start-up. Confirm
the pin setting and communication rate as well.
５５ソウシンゴノＡＡガジュシンデキマセン
No AA replyed from target after 55 sent
An adjustment error. Confirm the pin setting and
communication rates.
５５ソウシンゴニＡＡイガイガジュシンサレマ
シタ
Instead of AA other reply backed for 55
イレースニシッパイシマシタ
Failed at erasing flash memory
Possibly, due to wrong MCU selection, or MCU
built-in FLASH memory is broken. Reconfirm
selected MCU model name.
ＴＧＰガドウサシテイマセン
Correct response did not back from TGP
ＴＧＰガイジョウデス
Wrong reply was received from TGP
シリアルノセッテイニシッパイシマシタ
Failed at serial communication parameter
Possibly, incorrect pin setting or too quick a
communication rate during boot start-up.
Confirm the pin setting and communication rate as
well.
５５ソウシンゴノＥ６ガジュシンデキマセン
E6 did not back as reply for 55
５５ソンシンゴニＥ６イガイガジュシンサレマ
シタ
Wrong reply backed to E6 after sending 55
ニュウリョクサレタビットレートガセンタクデ
キマセン
Input value for bitrate is wrong to use
Possibly, too quick a maximum asynchronous
communication rate.Confirm the above rate.
ビットレートセッテイゴノＡＣＫガジュシンデ
キマセン
Failed to get recept for bitrate setting
ブートモードキドウジニＲＸＤタンシガＬＯＷ
ノママデシタ
RXD port stays low in bootmode starting
Possibly, communication pin is not connected
properly in the circuit. Confirm connection.
ブートモードキドウジニＲＸＤタンシガＨＩＧＨ
ノママデシタ
RXD port stays high in bootmode starting
ＴＧＷカキコミアドレスガセッテイデキマセ
ン
Failed to set programming address of TGW
Possibly, too quick amaximum asynchronous
communication rate/a synchronous communication
rate.Confirm the above rates.
カキコミエラーガハッセイシマシタ
Programming error occured
Please reconfirm connection and setting contents.
ビットレートセンタクゴノカクニンコードガジ
ュシンデキマセン
Confirmation code cannot be
received
バイトベリフェイエラーデス
Disagreement found in verifying
Other errors
Please format a card
Resulting from other than FAT12/16/other errors
Possibly due to broken file, inappropriate format or broken
CF. Try to recover by checking disk, save or format again.
Don’t select FAT32 when formatting CF.
File system error
Resulting from obtaining a file (folder) list from the
Root
File may be broken, inappropriate format, or CF broken.
Try to recover by checking disk, save or format again.
Please insert a card
Card not inserted
Insert CF of FAT12/FAT16 into the body.
Can't open INI file
With formatted CF, a file is not found to save
system setting, or other errors
Can move forward by pushing either button. When writing,
modifying set-up, or making keylock, a file to save system
setting is produced, and no error message occurs from
then on. There are maybe damaged files, inappropriate
format, or broken CF. Check the disk, save and format
again.
INI put error
Can
’t load from a file to save system setting
Possibly due to damaged file, inappropriate format, or
broken CF. Try to check the disk, save and format again.
INI get error
Can
’t write in a file to save system setting
CURFILE not found
An early-selected file set in the system is not in the
CF.
Can move forward by pushing either button. Writing or
modifying set-up updates and improves files to save
system setting.
Can't open HDP file
Project file absent, name of folder is different from
that of project file, or other errors
Confirm file name. Possibly due to damaged file,
inappropriate format, or broken CF. Try to check the disk,
save and format again.
HDP get error
Can
’t load from project file.
Possibly due to damaged file, inappropriate format, or
broken CF. Try to check the disk, save and format again.
Can't open HDH file
File of host program absent, or different one found
other than host program setup in the project
Host program is found but error messages are displayed.
Possibly due to damaged file, inappropriate format, or
broken CF. Try to check the disk, save and format again.
HDH illegal version
Something is wrong with version information of
host program
Possibly due to damaged file, inappropriate format, or
broken CF. Try to check the disk, save and format again.
HDH get error
Can
’t load from file of host program
HDH check sum error
When file of host program is loaded and sum is
calculated, the sum is different from that of the file
pin
File not found
No file (folder) to write in is found.
Transmit data by USB connection, or save data by
over-the-counter CF reader and then insert file into
FM-ONE.
Self test NG
It is reported that the result of selftest is NG.
Please set the switch (for farmware update) to
normal position and
reconnect.
note: please refer to page3 for details.