136
Section 5 - Scheduled Maintenance
5.23 SK5500 Maintenance Matrix
SK5500 Maintenance Matrix
EQUIPMENT
COMPONENT
INTERVALS
LUBRICATION SPECIFICATIONS
Truck Engine
Oil and Filter
Refer to Truck Operating
Manual
Refer to Truck Operating Manual
Driveline
Transmission, Drive shafts,
Differential
Refer to Truck Operating
Manual
Refer to Truck Operating Manual
Creep Drive
Muncie SS88
1 time per year or 500 hours
75/90 (Full Synthetic)
Jack Shaft
Shaft Between Muncie
PTO and Hydrostatic Pump
Weekly
Mobile Poly Rex Type Em
Hydraulic System
Hydraulic Fluid Reservoir
(5 gal)
500 hours or every 1 year
AW 68 or Equivalent
Hydraulic System
High Pressure Hydraulic
Filter
After First 100 hours
then every 500 hours
AW 68 or Equivalent
Hydraulic System
Return Hydraulic Filter
After First 100 hours
then every 500 hours
Hydraulic Filter
Roots Vacuum Blower
Blower Gear Case oil
( 1 Quart )
After First 50 hours and then
every 2000 hours
ISO VG 320 Roots Oil
Dresser Roots Blower
Pulley End Bearings
(Grease Fittings)
1 time each week
(2 pumps Each Fitting)
High Temp - Synthetic
Howden Roots Vacuum
Blower
Pulley End Bearings
(Grease Fittings)
1 time each week
(2 pumps Each Fitting)
Royal Purple
Tuthill Blower
Pulley End Bearings
(Grease Fittings)
Daily
(2 pumps Each Fitting)
Tuthill
Roots Vacuum Blower
Vacuum Filter
Inspect Daily
ISO VG 320 Roots Oil
High Temp - Synthetic
Kunkle Valve
Vacuum Relief Valve
Cycle Daily
WD-40 or Equivalent
Jetstream Pump
Stuffing Boxes
Every 100 hours
NA
Jetstream Pump
Connecting Rod Bearings
500 hours
NA
Jetstream Pump
Uni-valves
Every 100 hours
(Lapping Procedure)
NA
Jetstream Pump
Crankcase Oil (9 gal)
After First 100 hours and then
every 500 hours
75/90
Hog Head
HD Motor Centering
Adjustment
200 hours
NA
Hog Head
Thru-Shaft rpm sensor gap
As needed
NA
Hog Arm
Chassis Wheels And Casters
Daily
General Purpose Grease
General Grease Points
Door Hinges, Debris Tank
Tilt Pins, Vacuum Door
Hinges, Ball Valves,
Latches, ETC
Weekly
More Frequently If Required
General Purpose Grease
This chart is a guide only. It should never be used to supersede original manufacturer specifications. Refer to the
manufacturer's operation and maintenance manuals.
Содержание SK5500
