Hoffmann MS35-SF-TP Скачать руководство пользователя

Страница: 65 / 114

Operating and Maintenance Manual

HOFFMANN MS35SF-TP Double Miter Saw

• Version 7.148.66 • 06-2017

17.6.1

Trouble Shooting Chart

Error #

Indication

Reason

Remedy

Saw motors will not start

Motors have not been switched on

No power to motors

Overheated

Press saw motor start button.

Check all electrical connections

Check motor overload breakers in
electrical cabinet.

Allow motors to cools down.

Router motors will not start

Motors have not been switched on

No power to motors

Check switches on motors

Check power cords for internal
damage.

Check for proper connection

Saw and/or router speed (rpm’s)
decrease

Dull tooling

Feed rate to high

Check and replace tooling
(saw blades and/or router bits)

Adjust feed rates with flow control
valves in pneumatic control cabinet

Loud noise during machining
cycle.

Dull or damaged tooling.

Wrong saw blade rotation.

Check and replace tooling
(saw blades and/or router bits)

Change rotation.

Bad miter cut result.

Saw blades are dull or damaged.

Replace saw blades

– use original

HOFFMANN blades for best
results.

Router won’t move freely.

Guides and/or tracks dirty.

Clean tracks and guide rods.

Cutting angle off (not 45.0
degrees)

Dirt trapped between saw blade flange
and saw blade

Position of blade arbor blocks incorrect.

Remove blade and clean flange
and blade.

Adjust blade arbor blocks.

Keyway location offset from left to
right hand work piece

Router stops not adjusted properly

Adjust keyway locations with digital
counters.

Machin

e won’t start

Machine tables are not closed
completely

Press “set-Up” button to close
tables

Machine tables won’t open

Cylinder sensor does not trigger.

Cylinder sensor defective.

Remove debris inside machine to
allow saw carriage to travel to end
position

– DO NOT move cylinder

sensor!

Replace defective sensor.

Machine tables open too soon or
too late for proper operation

Cylinder sensors misadjusted.

Adjust cylinder sensors.

Содержание MS35-SF-TP



















































































































Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды

Hoffmann MS35-SF-TP, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды