Hoffmann MS35-SF-TP Скачать руководство пользователя

Страница: 60 / 114

Operating and Maintenance Manual

HOFFMANN MS35SF-TP

Double Miter Saw

• Version 7.148.66 • 06-2017

16.10

Faults

– Errors - Emergencies



Only qualified and trained personnel

may perform troubleshooting and testing
procedures!



Person not involved with trouble

shooting shall remain a safe distance from
machine until normal operation is
restored.

In case of emergency press
Emergency Stop Button.

Activating the emergency stop button will stop
saw and router motors and return all
carriages back to their home positions.

The material clamping cylinders remain under
pressure and must be deactivated separately.

16.10.1

Emergency Stop reset

Upon activating the Emergency Stop
Switch (1) follow these steps to re-set
the machine controls:

1. Release red E-Stop button (1).

2. Switch on machine control panel (2).

3. Press CONFIRM Button (3) to bring all tables back

to their home positions.

WARNING!

Shutting off machine or disconnecting
electrical power supply will not
disconnect compressed air supply.
Pneumatic circuit remains under
pressure even when main power
switch is switched-off and locked!

Содержание MS35-SF-TP



















































































































Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды

Hoffmann MS35-SF-TP, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды