manualshive.com logo in svg

HME Clear-Com 104G070, Руководство по установке

Поделиться
Скачать
HME Clear-Com 104G070 Скачать руководство пользователя страница 11

© 2022 HME Clear-Com Ltd. All rights reserved.

7

Fig. 13

Place one transceiver in the desired location and determine the distance/location where the LED 

flashes RED this is the coverage limit of that transceiver. If you need additional coverage area, add 

additional transceivers to extend the coverage area�

OVERLAPPING TRANSCEIVERS 

From the point where you got a Red LED, place the new transceiver back 15 ft (4�6 m) from the 

Edge of transmission where you got the Red LED to create an overlapping coverage zone�
To achieve desired reliability and signal diversity, each  transceiver requires two channels to op-

erate� For example, a system with four transceivers would need eight channels to operate� In a 

smaller system with four transceivers or less, there are generally enough available channels in the 

spectrum such that there is no need to worry about channel overlapping� 
It’s possible to re-use the channel of the transceiver, given that the devices are far apart enough so 

one does not interfere with the other’s RF space� It is important to assure that a beltpack sees no 

more than one transceiver with the same pair of channels in any coverage area location�

Fig. 14

Содержание Clear-Com 104G070



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды