HME Clear-Com 104G070 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 18

background image

© 2022 HME Clear-Com Ltd. All rights reserved.

6

TRANSCEIVER PLACEMENT

To determine transceiver placement: survey desired coverage area and to determine how many

transceivers are required to cover usage areas� Because EQUIP allows you to deploy up to four

transceivers for seamless coverage, place your transceivers in locations that will allow for roaming�

Transceiver Placement: Height 8-40 feet (2�4–12 meters)� Position (Vertical)� Angle 15% down

when mounting > 15 feet (4�5 meters)�

Before running a site survey, first connect all the transceivers and run auto scan or set channels

manually (see "Transceiver 5 GHz Radio Channels" on page 9 and "Manually Setting 5 GHz

Channels" on page 10)�

SITE SURVEY

To put the EQUIP base station in site survey mode, go to SYSTEM>SETTINGS and select Remote

Transceiver from the drop-down list (see Fig� 11)�

Fig. 11

Tap the Site Survey button (see Fig� 12) and follow the onscreen prompts (Fig� 12 and 13)�

Fig. 12

«
...
8
9
10
11
12
...
»

Содержание Clear-Com 104G070



















Отзывы:

Нет отзывов

Похожие инструкции для Clear-Com 104G070

Бренд: National Instruments Страницы: 8

Бренд: iDance Страницы: 10

ioControl CR2050

Бренд: IFM Страницы: 126

Бренд: Vandersteen Audio Страницы: 20

Бренд: Panasonic Страницы: 4

Бренд: Spon Страницы: 9

CPX-AP-I-8DI-M8-3P

Бренд: Festo Страницы: 18

Бренд: PYLE Audio Страницы: 4

Бренд: Sandstrom Страницы: 32

Бренд: RAM Страницы: 22

Бренд: iLive Страницы: 8

Бренд: Roadstar Страницы: 23

Бренд: WAGO Страницы: 12

Бренд: Lynx Страницы: 27

Бренд: Jensen Страницы: 3

Бренд: Sandstorm Страницы: 20

Бренд: Audiovox Страницы: 8

Weymouth Series

Бренд: Hamworthy Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды