HKS 70019-AF011 Скачать руководство пользователя страница 1

                                                        

E04511-F45020-00 

- 1 - 

SUPER POWER FLOW Reloaded 

Intake Kit 

70019-AF011 

SUBARU LEGACY

 

Engine Type: EJ25 TURBO / Chassis Type: BM9.BR9 

Model Year: 2009/5-

 

 

Ver. 20100310 

NOTICE 

This manual assumes that you have and know how to use the tools and equipment necessary 
to safely perform service operations on your vehicle. This manual assumes that you are familiar 
with  typical  automotive  systems  and  basic  service  and  repair  procedures.  Do  not  attempt  to 
carry  out  the  operations  shown  in  this  manual  unless  these  assumptions  are  correct.  Always 
have access to a factory repair manual. To avoid injury, follow the safety precautions contained 
in the factory repair manual. 

 

SAFETY PRECAUTIONS 

WARNING 

  To prevent electrical damage/burns/fires, always: 

-  Disconnect the negative terminal of the battery before beginning installation. 
-  When disconnecting wires/connectors, take extra care to avoid breaking/snapping the 

connectors. 

 

CAUTION 

  Do not misuse this product. 

-

  Misuse of this product may lead to engine damage. 

-

  Misuse of this product may lead to loss of original function. 

  Prior to installation, make sure the engine bay temperature has cooled to approximately 

40

/104°F 

-  Failure to let the engine cool down properly can lead to severe burns. 

  Insert clean rags into open piping to prevent contaminants from entering the pipes.  

-  If neglected, contaminants in the piping can lead to engine damage. 

 

-

  Make sure that all of the parts listed in the Parts List are included in the kit. 

-

  Reference the factory service manual for the vehicle when removing factory parts.  

-

  Be careful when handling this product; avoid dropping or subjecting it to excessive impact. 

Failure to do so may result in product damage or improper installation. 

-

  Use the proper tools when tightening nuts and bolts. If over tightened, the bolts may 

become damaged. 

-

  Keep the removed factory parts in a safe place for ease of re-installation at a later date (if 

necessary). 

-

  Replace the air filter element at regular intervals: 

(Recommended) Replace every 6,000~10,000km/4,000-6,400miles or every 6~12 months.  
Replacement air filters are sold separately. 
*Do not wash the air filters as the filtration properties will be degraded.  

-  There are certain conditions where, depending on dirt buildup, the filter may need to be 

replaced earlier than the above recommended intervals

-  If the vehicle and the product are not maintained properly as mentioned above, the product 

may not perform properly and the airflow meter sensor may not be able to detect the intake 
air volume accurately; it can lead to engine damage or faulty conditions.

 

 

Содержание 70019-AF011








Отзывы: