Hiwin 25.12345 Скачать руководство пользователя страница 21

Страница: 21 / 64

Transport and installation

Assembly Instructions

Linear Tables HT-L

HTL-01-0-EN-1905-MA

Transport and installation

5.1 Delivery

5.1.1 Delivery state

The linear tables HT-L are supplied fully assembled and function tested.

5.1.2 Scope of delivery

The contents of delivery vary depending on the ordered model, accessories, and options.

5.2 Transport to the installation site

Damage to the linear tables!

The linear tables may be damaged by mechanical loading.

Hoist the linear tables only at the designated points (see Section 5.5)!

For longer linear tables, provide additional protection of the centre section!

Ensure that the linear tables do not bend as this could permanently damage accuracy!

During transport, do not transport any additional loads on the linear tables!

Provide heavy attachments with additional supports!

ATTENTION!

5.3 Requirements at the installation site

5.3.1 Ambient conditions

Ambient temperature +5 °C to +40 °C, non condensing

Installation site

flat, dry, vibration-free

Atmosphere

not corrosive, not explosive, no vacuum

Danger from suspended loads or falling parts!

Lifting heavy loads may damage your health!

Only qualified personnel may assemble, install, and service the linear tables!

Note the mass when transporting the parts. Use suitable hoisting gear!

Observe the applicable occupational health and safety regulations when handling suspended loads!

Hoist the linear tables only at the designated points!

Secure machinery and machine parts against tilting!

WARNING!

The linear tables are precision products and must be treated with care. Impacts of any kind may damage the axis. The result

may be compromised running precision and service life. Transport the packaged product as close as possible to its installa-

tion site. Remove the packaging at this site only.

Danger of impacts and crushing!

If the axes are moved/driven manually, injuries can be caused by moving axes and attachments (energy

chains, attachments installed by customer).

Observe the applicable occupational health and safety regulations!

Transport to the installation site only by qualified personnel!

CAUTION!

Содержание 25.12345

































































Результаты поиска

Содержание 25.12345

Отзывы:

Похожие инструкции для 25.12345

Бренды по названию

Популярные бренды

Hiwin 25.12345, Руководство по сборке

Результаты поиска

Содержание 25.12345

Отзывы:

Похожие инструкции для 25.12345

Бренды по названию

Популярные бренды