Hitecsa CLVBA-CLVA 401 Скачать руководство пользователя страница 9

Страница: 9 / 18

IOM_CLVBA-CLVA_401_208095_200801_EN

CLVBA-CLVA

EVAPORATION UNITS AIR-AIR

INSTALLATION

INSTALLATION LOCATION

Consult and respect the rules and local regulations which regulate the installation of air conditioning systems.

Choose a site without dust and debris.

Respect the appropriate service area for the equipment which will be installed.

Verify that the ground or structure on which the unit will be installed is able to support its weight in operation.

Fit shock absorbers throughout the installation to prevent the transmission of noise and vibration.

Check that the direction of the sound level is not going to disturb anyone.

UNIT SETTLEMENT



Make sure that the unit is correctly levelled.



The bed frame should have the area and the strength to support the weight of the unit.



Be sure that after settlement the unit drain is working properly.

SERVICE AREA (mm)

Make sure to respect the following measurements for the correct operating of the unit.

WEIGHT DISTRIBUTION

(kg)

CLVA-BA

TOTAL

401

20.5

Содержание CLVBA-CLVA 401



















Результаты поиска

Содержание CLVBA-CLVA 401

Отзывы:

Hitecsa CLVBA-CLVA 401, Инструкция по установке, эксплуатации и обслуживанию, Страница: 9 / 18

Результаты поиска

Содержание CLVBA-CLVA 401

Отзывы: