background image

English   

- 4 -

 Introduction 

 Thank you for choosing this product. This 

manual will guide  you for the proper 

operation of your TV. Before operating 

the TV, please read this manual 

thoroughly. 
Please do keep this manual in a safe 

place for future references. 

 Preparation 

 For ventilation, leave a free space of at least 

10 cm all around the set. To prevent any fault 

and unsafe situations, please do not place any 

objects on top of the set.
Use this device in moderate climates. 

 

10  cm

10
 cm

10

 cm

 

 Safety Precautions 

 Please read the following recommended 
safety precautions carefully for your 
safety.

 Power Source 

 The TV set should be operated only from a  220-

240 V AC, 50 Hz  outlet. 

 Power Cord 

 Do not place the set, a piece of furniture, etc. 

on the power cord (mains lead) or pinch the 

cord. Handle the power cord by the plug. Do 

not unplug the appliance by pulling from the 

power cord and never touch the power cord with 

wet hands as this could cause a short circuit or 

electric shock. Never make a knot in the cord or 

tie it with other cords. The power cords should 

be placed in such a way that they are not likely 

to be stepped on. A damaged power cord can 

cause   re or give you an electric shock. When it 

is damaged and needs to be replaced, it should 

be done by quali  ed personnel. 

 Moisture and Water 

 Do not use this device in 

a humid and damp place 

(avoid the bathroom, the 

sink in the kitchen, and near 

the washing machine). Do 

not expose this device to 

rain or water, as this may be 

dangerous and do not place 

objects filled with liquids, 

such as vases, on top. Avoid 

dripping or splashing.
If any solid object or liquid falls into the cabinet, 

unplug the TV and have it checked by quali  ed 

personnel before operating it any further.  

 Cleaning 

 Before cleaning, unplug the 

TV set from the wall outlet. 

Do not use liquid or aerosol 

cleaners. Use soft and dry 

cloth.  

 Ventilation 

 The slots and openings on the 

TV set are intended for ventilation and to ensure 

reliable operation. To prevent overheating, these 

openings must not be blocked or covered in 

anyway. 

 Heat and Flames 

 The set should not be placed 

near to open flames and 

sources of intense heat such 

as an electric heater. Ensure 

that no open   ame sources, 

such as lighted candles, 

are placed on top of the TV. 

Batteries should not be exposed to excessive 

heat such as sunshine,   re or the like. 

 Lightning 

 In case of storm and lightning 

or when going on holiday, 

disconnect the power cord 

from the wall outlet.  

 Replacement Parts 

 When replacement parts are required, make 

sure that the service technician has used 

replacement parts, which are speci  ed by the 

manufacturer or have the same speci  cations as 

A00_[GB]_MB35_UKIDTV_SILVER1_42842W_3900UK_10065638_50156582.indd   4

A00_[GB]_MB35_UKIDTV_SILVER1_42842W_3900UK_10065638_50156582.indd   4

03.10.2009   14:18:40

03.10.2009   14:18:40

Содержание L42VK05U


























































Отзывы: