Hitachi HVM Navigator V03-06 Скачать руководство пользователя страница 295

Страница: 295 / 312

Troubleshooting

6-33

HVM Navigator User's Guide - Migration

Detailed error information detected by Migration Management

Server

Format

“EMG” op1 : op2 : don’t_care : (op3) : ”MMS” : message

•

“EMG”: Fixed characters meaning error message.

•

“MMS”: Fixed characters meaning Migration Management server.

•

don’t_care: Values at this position are negligible.

•

op1: 1st operand that identifies error detail in hexadecimal code. See
Description.

•

op2: 2nd operand that identifies supplementary information in hexadecimal
code. See Description.

•

op3: 3rd operand that identifies reason in hexadecimal code. See

Description.

•

Message: Shows error detail in text. See Description.

Table 6-2 Error message detected by MMS

op1

op2

op3

Message [interpretation]

Suggested action

0x00 00000001 0020 02
0x00 00000002 0020 02

0x0000 0000 0000 0000 0x01 Connection refused (MMS-

Blade)
[Migration Management
module (MMS) cannot
connect to specified server

blade.]

Check the following, make
corrections if necessary,

and then retry migration:
The specified server blade
(HVM) is up and running.
Communication to the IP
address of the specified

server blade is established.

0x00 00000003 0020 02 0x0000 0000 0000 0000 0x01 The specified blade is busy.

Please wait until another

migration is completed.

Check if the same server
blade is specified as source

and destination.
Wait for completion of
preceding migration and

then retry migration.

0x00 00000003 00A0 02 0x0000 0000 0000 0000 0x01 Specified NIC was not found.

(Src-Blade)

Check if you set a migration
path properly on the source

server blade and retry.

0x00 00000003 00A5 02 0x0000 0000 0000 0000 0x01 Specified NIC was not found.

(Dst-Blade)

Check the setting of a
migration path on the
destination server blade

and retry.

0x00 00000004 0020 02 0x0000 0000 0000 0000 0x01 The specified blade is busy.

Please wait until another

operation is completed.

Wait for completion of
ongoing operation and then

retry migration.

0x00 00000005 00B0 02 0x0000 0000 0000 0000 0x01 Can not assign the same IP

for the source and the

Destination.

Check the setting of a
migration path for source
and destination server
blades and set a different IP

addresses for each of them.

Содержание HVM Navigator V03-06

























































































































































































































































































































Результаты поиска

Содержание HVM Navigator V03-06

Отзывы:

Hitachi HVM Navigator V03-06, Руководство пользователя, Страница: 295 / 312

Результаты поиска

Содержание HVM Navigator V03-06

Отзывы: