Hitachi G 10SS Скачать руководство пользователя страница 7

Страница: 7 / 76

English

STANDARD ACCESSORIES

(1) Wrench ........................................................................ 1
(2) Side handle ................................................................ 1
Standard accessories are subject to change without
notice.

APPLICATIONS

䡬

Removal of casting fin and finishing of various types
of steel, bronze and aluminum materials and castings.

䡬

Grinding of welded sections or sections cut by
means of a cutting torch.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.

3. Extension cord

When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent
injury should the depressed center wheel shatter
during operation. Ensure that the guard is properly
fitted and fastened before commencing grinding
operation.

By slightly loosening the setting screw, the wheel
guard can be turned and set at any desired angle
for maximum operational effectiveness. Ensure that
the setting screw is thoroughly tightened after
adjusting the wheel guard.

Ensure that mounted wheels and points are fitted
in accordance with the manufacturer’s instructions.
Ensure that the depressed center wheel to be utilized
is the correct type and free of cracks or surface
defects. Also ensure that the depressed center wheel
is properly mounted and the wheel nut is securely
tightened, Refer to the section on “ASSEMBLING
AND DISASSEMBLING THE DEPRESSED CENTER
WHEEL”
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they
are required.
Do not use separate reducing bushings or adaptors
to adapt large hole abrasive wheels.
For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
Do not use cutting off wheel for side grinding.

6. Conducting a trial run

Ensure that the abrasive products is correctly
mounted and tightened before use and run the tool
at no-load for 30 seconds in a safe position, stop
immediately if there is considerable vibration or if
other defects are detected.
If this condition occurs, check the machine to
determine the cause.

7. Confirm the push button

Confirm that the push button is disengaged by
pushing push button two or three times before
switching the power tool on (See

Fig. 2

8. Fixing the side handle

Screw the side handle into the gear cover.

SPECIFICATIONS

*Be sure to check the nameplate on product as it is subject to change by areas.

–

If a guard is equipped with the tool never use the
tool without such a guard;

–

Do not use separate reducing bushings or adapters
to adapt large hole abrasive wheels;

–

For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length;

–

Check that the work piece is properly supported;

–

Do not use cutting off wheel for side grinding;

–

Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable
substances;

–

Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, first disconnect the tool
from the mains supply (use non metallic objects)
and avoid damaging internal parts;

–

Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn;

–

Pay attention to the wheel that continues to rotate
after the tool is switched off.

Model

G10SS

G12SS

G13SS

Voltage (by areas)*

(110V, 120V, 220V, 230V, 240V)

Power Input*

580 W