Hitachi DS 14DMR Скачать руководство пользователя страница 26

Страница: 26 / 59

--- 23 ---

CAUTION

•

For safe operation, see Instruction Manual.

•

Charge HITACHI rechargeable batteries Type EB 7, EB 9,

EB 12 and EB 14 series. Other types of batteries may
burst causing personal injury and damage.

•

Charge between 32 and 104

•

Indoor use only.

•

Replace defective cord immediately.

CAUTION

•

Read thoroughly HANDLING INSTRUCTIONS

before use.

•

Do not disassemble nor throw into fire.

CAUTION

•

Read thoroughly HANDLING INSTRUCTIONS

before use.

CAUTION

•

For safe operation, see Instruction Manual.

•

Use HITACHI charger recommended in instruction manual

for recharging.

(9) Do not attempt to disassemble the storage battery or the charger.

Special devices, such as a thermostat, are built into the storage battery and charger to permit rapid charging.

Incorrect parts replacement and/or wiring will cause malfunctions which could result in fire or other hazards.

Instruct the customer to bring these units to an authorized service center in the event repair or replacement is

necessary.

(10) Disposal of the storage batteries

Ensure that all customers understand that the Storage Batteries should be returned to the Hitachi power tool

sales outlet or authorized service center when they are no longer capable of being recharged or repaired. If

thrown into a fire, the batteries may explode, or if discarded indiscriminately, leakage of the cadmium

compound contained in the battery may cause environmental pollution.

B. Caution Plates

(1) The following precautions are listed on the Name Plate or Caution Plate attached to the main body of each

tool.

For the U.S.A. and Canada

(3) The following caution is listed on the Name Plate attached to the Model UC 14YFA Charger.

For the U.S.A.

For Oceania

For the U.S.A. (excludes French) or Canada

WARNING

•

To reduce the risk of injury, user must read and

understand Instruction Manual.

AVERTISSEMENT

•

Afin de réduire le risque de blessures, I'utilisateur doit lire

et bien comprendre le mode d'emploi.

(2) The following cautions are listed on the Name Plate attached to each storage battery.

For Europe

Содержание DS 14DMR




























































Результаты поиска

Содержание DS 14DMR

Отзывы:

Hitachi DS 14DMR, Технические данные и руководство по обслуживанию, Страница: 26 / 59

Результаты поиска

Содержание DS 14DMR

Отзывы: