Hitachi DS 14DMR Скачать руководство пользователя страница 11

Страница: 11 / 59

--- 8 ---

Model

Cordless impact driver

WH 18DMR

Capacity

Item

Cordless impact wrench

WR 18DMR

Small screw M4 --- M10 (5/32" --- 3/8")*

Ordinary bolt M6 --- M14 (1/4" --- 9/16")
High-strength bolt M6 --- M12 (1/4" --- 15/32")

Ordinary bolt M10 --- M16 (3/8" --- 5/8")
High-strength bolt M8 --- M14 (5/16" --- 9/16")

Tightening torque

150 N

•

m (1530 kgf

•

cm, 1330 in-lbs.)*

220 N

•

m (2245 kgf

•

cm, 1950 in-lbs.)*

Tip condition

6.35 mm (1/4") Bit holder

12.7 mm (1/2") Square drive

Type of motor

Fan cooled rare-earth magnet motor

Enclosure

Main body: Polyamide resin + elastomer

• • • • • •

Housing

Aluminum alloy die casting

• • • • • • • • •

Hammer case

Elastomer

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Protector

Storage battery: Polyamide resin (black)
Charger: ABS resin (black)

Type of switch

Trigger switch with forward/reverse changeover pushing button (with brake)

Handle configuration

T-type

No-load rotational speed

0 --- 2,600 /min

Impact rate

0 --- 3,200 /min

Main body

2.0 kg (4.4 lbs.) (Includes battery)*

Battery

1.04 kg (2.2 lbs.)

Overall length x height

162 mm (6-3/8") x 236 mm (9-19/64")

Center height

27 mm (1-1/16")

Battery
(Type EB 1820L)

Sealed cylindrical nickel-cadmium batteries
Nominal voltage: DC 18 V
Nominal life: Charging/discharging approximately 300 cycles

(in the case of the Model UC 18YG)

Nominal capacity: 2.0 Ah

167 mm (6-37/64") x 236 mm (9-19/64")

Battery
(Type EB 1826HL/
EB 1830HL)

Sealed cylindrical nickel-metal hydride batteries
Nominal voltage: DC 18 V
Nominal life: Charging/discharging approximately 500 cycles

(in the case of the Model UC 24YFA)

Nominal capacity: 2.6 Ah/3.0 Ah

Weight

Charger
(UC 24YFA)

Overcharge protection system:
(1) Battery voltage detection (

V system) for Ni-Cd battery

Mi-MH battery temperature detection (dT/dt system) for Ni-MH battery
(2) Battery surface temperature detection (thermostat or thermistor)
(3) 120-minute timer
Power input: 90 W
Charging time: Approx. 50 minutes [for type EB 1820L battery at 20

C (68

F)]

Approx. 60 minutes [for type EB 1826HL battery at 20

C (68

F)]

Approx. 70 minutes [for type EB 1830HL battery at 20

C (68

F)]

Operable ambient temperature range: 0

C --- 40

C (32

F --- 104

The maximum allowable temperature of the EB 1820L battery is 60

C (140

F) and

the type EB 1826HL or EB 1830HL battery is 45

C (113

F).

Models WH 18DMR/WR 18DMR

Содержание DS 14DMR




























































Результаты поиска

Содержание DS 14DMR

Отзывы:

Hitachi DS 14DMR, Технические данные и руководство по обслуживанию, Страница: 11 / 59

Результаты поиска

Содержание DS 14DMR

Отзывы: