Hioki ST5520 Скачать руководство пользователя страница 76

Страница: 76 / 201

Preventing Operation Errors at the Start of Testing (Double action function)

5.5 Preventing Operation Errors at the Start of

Testing (Double action function)

This is a function to prevent operation errors at the start of test and ensure safer test.
No tests start unless the

START

key is pressed within 1 s after the

STOP

key

is pressed when the double action function is set to ON. When the START is
enabled,

is displayed in the Measurement screen.

Operation errors can be prevented since the

STOP

key must be pressed before the

START

key is pressed.

Open the Settings screen.

Select

[SET]

Set

[DOUBLE ACTION]

[ON]

Selection

[ON]

[OFF]

Return to the
Measurement
screen.

•

When the double action function is set, the beeper sounds and the Error screen
is displayed if the

START

key is pressed without pressing the

STOP

key.

•

When the

START

is enabled,

is displayed in the Measurement screen.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 76 / 201

Результаты поиска

Содержание ST5520

Отзывы: