Hioki ST5520 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 201

Hioki ST5520 Скачать руководство пользователя страница 59

51

During Measurement

4.2 During Measurement

The instrument applies test voltage to equipment to be measured during
measurement.

1

When the test duration is set to

[ON]

1. When the

START

key is pressed, test voltage is applied to the equipment to be

measured, and the timer countdown starts. The remaining time is displayed in the test
duration indicator (TIMER).

2. During the response time,

[D]

is displayed on the left edge of the countdown time

indicator, and the measured value indicator becomes blank (no display). The display
during the response time is the same for both response time settings,

[AUTO]

and

[MANUAL]

.

3. After the response time has elapsed, the resistance measurement is performed for the

time specified for the timer, and the measured value is displayed. (Unit: M

Ω

) When the

comparator function is set, judgment is performed according to the test mode setting.

2

When the test duration is set to

[OFF]

1. When the

START

key is pressed, test voltage is applied to the equipment to be

measured, and the timer count-up starts. The time elapsed since the

START

key was

pressed is displayed in the test duration indicator (TIMER).

2. During the response time,

[D]

is displayed on the left edge of the count-up time

indicator, and the measured value indicator becomes blank (no display). The display
during the response time is the same for both response time settings,

[AUTO]

and

[MANUAL]

.

3. After the response time has elapsed, the resistance measurement is performed until

the

STOP

key is pressed, and the measured value is displayed. (Unit: M

Ω

) The

elapsed time is counted and displayed up to 999.9 s, but the resistance measurement
is performed until the

STOP

key is pressed. When the comparator function is set,

judgment is performed according to the test mode setting.

3

PASS/FAIL judgment display for the comparator function

Upper limit value ≤ Measured value

U.FAIL turns on.

Lower limit value < Measured value < Upper limit value

PASS turns on.

Measured value ≤ Lower limit value

L.FAIL turns on.

Refer to “3.7 Announcing the Judgment Results Using a Beep Sound” (p. 47) to set

beep sound for PASS/FAIL judgment.

When the upper and lower limit values are not set, the indicator displays “----” and

PASS/FAIL judgment is not performed. If either of the upper and lower limit values is set,

PASS/FAIL judgment is performed according to the value. (p. 44)

If the upper and lower limit values are set to values outside of the accuracy range, the

U.FAIL and L.FAIL lamps turn on at the same time.

4

The timer indicator indicates the test duration countdown. When the test
duration is not set, the indicator displays elapsed time.

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

«
...
57
58
59
60
61
...
»

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов