Hioki ST5520 Скачать руководство пользователя страница 54

Страница: 54 / 201

Setting the Test Mode

3.6

Setting the Test Mode

There are four test modes: Continuous test, PASS STOP, FAIL STOP, and Forced
termination judgment.

Open the Settings screen.

Select

[SET]

Set the test mode.

Selection

[CONT]

[PASS]

[FAIL]

[SEQ]

Return to the
Measurement
screen.

[CONT]

(Continuous test mode)

Continues tests until the set test duration elapses
and outputs the judgment result every sampling.

[PASS]

(PASS STOP mode)

Terminates a test and outputs the judgment result
when PASS judgment is made.

[FAIL]

(FAIL STOP mode)

Terminates a test and outputs the judgment result
when FAIL judgment is made.

[SEQ]

(Forced termination judgment
mode)

Outputs the judgment result when the set test
duration elapses or at the time of STOP input (key,
RS-232C command, or EXT.I/O).

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 54 / 201

Результаты поиска

Содержание ST5520

Отзывы: