manualshive.com logo in svg

Hioki ST5520, Инструкция по эксплуатации, Страница: 36 / 201

Поделиться
Скачать
Hioki ST5520 Скачать руководство пользователя страница 36

28

Pre-Operation Inspection

Checking the insulation resistance test

Required items

Recommended resistor:  High voltage high resistance thick film resistor GS series

Manufacturer: 

KOA Corporation or equivalent

 

(Be careful with the working voltage and power.)

CAUTION

If the test voltage (power) exceeds the rated voltage (power) of the 

prepared resistor, the resistor may become damaged. 

(Example) When the insulation resistance of the equipment to be measured is 100 M

Ω

Maximum working voltage

1000 V

Rated power

0.5 W

Test voltage

500 V

1 

Prepare a resistor.

2 

Check that the test voltage is lower than the maximum working voltage of 
the prepared resistor.

Test voltage < Maximum working voltage of the prepared resistor

(Example: 500 V < 1000 V)

3 

Check that the value calculated from the test voltage and resistance 
is smaller than the rated power of the prepared resistor. (If the value 
calculated from the test voltage and resistance is larger than the rated 
power of the prepared resistor, change the resistor or the test voltage.)

Squared test voltage ÷ Resistance < Rated power of the prepared resistor

(Example: 500 V 

× 

500 V

100 M

Ω

= 0.0025 W  < 0.5 W)

4 

Set the test voltage to 500 V.

5 

Set the lower limit value to 90 M

Ω

 and the upper limit value to 110 M

Ω

.

6 

Connect the test leads to the prepared resistor.

7 

Start a test and check that the measured resistance matches the 
resistance of the prepared resistor and the comparator judgment result is 

[PASS]

.

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов