Hioki ST5520 Скачать руководство пользователя страница 32

Страница: 32 / 201

Connecting the Measurement Leads

2.2 Connecting the Measurement Leads

Connect the optional Hioki measurement leads to the measurement terminals.

Refer to “Options” (p. 2) for details.

Use the measurement leads (optional) specified by our company.

Connecting to the measurement terminals on the front panel

Red

Black

HIGH

LOW

Connect the red plug to the

HIGH terminal and the black

plug to the LOW terminal.

Connecting to the measurement terminals on the rear panel

LOW

Black

Red

HIGH

For contact check (p. 58)
(Do not use for 2-terminal measurements.)

Connect the red plug to the inside HIGH terminal and

the black plug to the inside LOW terminal.

(Do not use the outside terminals on the both ends.)

CAUTION

•

When the HIGH terminal is short-circuited to the ground, the voltage of

the LOW terminal will become high and it is dangerous for you to touch it.

Do not touch the equipment to be measured, measurement leads, HIGH

terminals, or LOW terminals during measurement (while the TEST lamp

is blinking).

• During testing, the test voltage will be output simultaneously from

the measurement terminals on the front of the instrument and the

measurement terminals on the rear of the instrument. Do not connect any

plugs to set of measurement terminals that is not in use.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 32 / 201

Результаты поиска

Содержание ST5520

Отзывы: