Hioki ST5520 Скачать руководство пользователя страница 28

Страница: 28 / 201

Screen Configuration and Operation Overview

1.4 Screen Configuration and Operation Overview

This instrument consists of a measurement screen and various settings screens.

The screen examples in this manual appear reversed (black on white) for best

visibility. The instrument screens, however, can actually be displayed only as white
characters on a black background.

Measurement screen

Displays the test voltage setting.
Displays the resistance range setting.
Displays the measurement speed setting.

Measured value

Moves to various settings
screens.
Use the F keys at the
bottom of the screen to
select a screen.

Upper limit
value

Lower limit value

The auto range is set.
(Nothing is displayed in

the manual range.)

Voltage
monitor value

Test duration

F key set items

SET

Moves to the Settings screen. (p. 33)

VOLT

Moves to the Test Voltage Settings screen. (p. 34)

COMP

Moves to the Comparator Settings screen. (p. 44)

LOCK

Executes the key lock function. (p. 65)

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 28 / 201

Результаты поиска

Содержание ST5520

Отзывы: