manualshive.com logo in svg

Hioki ST5520, Инструкция по эксплуатации, Страница: 184 / 201

Поделиться
Скачать
Hioki ST5520 Скачать руководство пользователя страница 184

Appx.

4

Influence of Capacitive Load

Appx. 4 

Influence of Capacitive Load

Pure resistance is assumed in the instrument specifications, however, some 

capacitance components are contained in the equipment to be measured. The higher 

the resistance is (small detected current), the more variability the influence of a 

capacitive load causes.

Influence on output voltage rise

The charge current of the instrument is 1.8 mA (less than 20 mA).
If a capacitive load, such as a capacitor, is connected, the time required for the output voltage to 
rise is affected. The time is calculated as follows.

CV = it (C: Capacitance (F), V: Voltage (V), i: Current (A), t: Time (s))

Example:  If a test voltage of 500 V is applied to a 1.0 µF capacitor, the time required for the 

output voltage to rise to 500 V is approximately 0.28 s, calculated by (1.0 µF × 500 
V)/1.8 mA.

If the equipment to be measured contains capacitive components, extend the test 
duration.

Repeat accuracy

Test condition: Connect and measure the resistance load and capacitive load in parallel. (See 

the figure below.)

(A film capacitor is used.)

Instrument

Connection diagram

As the test data shows below, measurements were performed for each resistance range and 
variation in the average of 100 measurements was calculated. The measured values were 
obtained with the capacitor charged.
(Test duration: Max. 100 s)

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов