Hioki ST5520 Скачать руководство пользователя страница 18

Страница: 18 / 201

Usage Notes

IMPORTANT

When using the instrument, be sure to use the connecting lead wires, etc.

specified by our company. When other cords and lead wires are used, accurate

measurement may not be possible because the connection becomes poor, etc.

Before connecting the power cord

WARNING

•

To avoid electric shock and to maintain the safety specifications

of this instrument, connect the power cord provided only to a
3-contact (two-con ground) outlet.

•

Use only the designated power cord with this instrument. Use of

other power cords may cause fire.

CAUTION

To avoid damaging the power cord, grasp the plug, not the cord, when
unplugging it from the power outlet.

IMPORTANT

Turn off the power before disconnecting the power cord.

Before connecting measurement leads

DANGER

To avoid electric shock and short circuit accidents, turn off all power
of the measurement target before connecting measurement leads.

WARNING

To avoid electrical accidents, use the designated wires or ones with more
than enough dielectric strength and current capacity.

UL1032 AWG18
Twisted wires

75 wires ×

0.12 mm

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 18 / 201

Результаты поиска

Содержание ST5520

Отзывы: