Hioki ST5520 Скачать руководство пользователя страница 15

Страница: 15 / 201

Usage Notes

Usage Notes

Follow these precautions to ensure safe operation and to obtain the full benefits of

the various functions.

Preliminary checks

DANGER

If the probe or the instrument is damaged, there is a risk of electric
shock. Before using the instrument, perform the following inspection.

•

Before using the instrument, check that the coating of the probes

are neither ripped nor torn and that no metal parts are exposed.

Using the instrument under such conditions could result in electric

shock. Replace the probes with those specified by our company.

•

Before using the instrument the first time, verify that it operates

normally to ensure that no damage occurred during storage or

shipping. If you find any damage, contact your authorized Hioki

distributor or reseller.

Installation

Installing the instrument in inappropriate locations may cause a malfunction of
instrument or may give rise to an accident. Avoid the following locations.

For details on the operating temperature and humidity, refer to the specifications.

(p. 151)

CAUTION

•

Exposed to direct sunlight or high temperature

•

Exposed to corrosive or combustible gases

•

Exposed to water, oil, chemicals, or solvents

•

Exposed to high humidity or condensation

•

Exposed to high quantities of dust particles

•

Susceptible to vibration

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 15 / 201

Результаты поиска

Содержание ST5520

Отзывы: