Hioki ST5520 Скачать руководство пользователя страница 145

Страница: 145 / 201

137

Command Reference

:COMParator:MODE

Sets the comparator test mode.

Syntax

:COMParator:MODE <data>

<data>

CONTinue, PASSstop, FAILstop, SEQuence (text data)

Example

To set the test mode to FAIL STOP

PC>

:COMParator:MODE FAILstop

:COMParator:MODE?

Queries the comparator test mode.

The test mode is returned in text data (<data>).

Syntax

:COMParator:MODE?

Response

:COMPARATOR:MODE <data>

or simply

<data>

<data>

CONTINUE/PASSSTOP/FAILSTOP/SEQUENCE (text data)

Example

To query the comparator test mode (when the test mode is FAIL STOP)

PC>

:COMParator:MODE?

ST5520>

:COMPARATOR:MODE FAILSTOP

(when

the

:HEADer

command is ON)

ST5520>

FAILSTOP

(when the

:HEADer

command is OFF)

:COMParator:BEEPer

Sets the beep sound at the time of comparator judgment and at the end of the timed duration.

Syntax

:COMParator:BEEPer <data>

<data>

PASS/FAIL/OFF/END (text data)

Example

To set to beep at FAIL judgment

PC>

:COMParator:BEEPer FAIL

:COMParator:BEEPer?

Queries the beep sound setting at the time of comparator judgment and at the end of the timed

duration.

The beep sound setting is returned in text data (<data>).

Syntax

:COMParator:BEEPer?

Response

:COMPARATOR:BEEPER <data>

or simply

<data>

<data>

PASS/FAIL/OFF/END (text data)

Example

To query the beep sound setting at the time of judgment (when the beeper

sounds at FAIL judgment)

PC>

:COMParator:BEEPer?

ST5520>

:COMPARATOR:BEEPER FAIL

(when

the

:HEADer

command is ON)

ST5520>

FAIL

(when the

:HEADer

command is OFF)

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 145 / 201

Результаты поиска

Содержание ST5520

Отзывы: