manualshive.com logo in svg

Hioki ST5520, Инструкция по эксплуатации, Страница: 140 / 201

Поделиться
Скачать
Hioki ST5520 Скачать руководство пользователя страница 140

132

Command Reference

:MEASure:COMParator?

Queries judgment result.

When this command is received during tests, the judgment result is returned in text data (<data>).

When the comparator function is OFF, OFF is always returned as a judgment result.

When no judgment is made, NOCOMP is returned. When the response time timer is ON, DELAY 

is returned.

After the test is completed, the judgment result when the previous test was completed is 

returned.
No command header is included in response.

Syntax

:MEASure:COMParator?

Response

<data>

<data>

Judgment result 

OFF /NOCOMP /DELAY /PASS /UFAIL /LFAIL /

ULFAIL (text data)

 

OFF: The judgment function is OFF.

 

NOCOMP: No judgment is made.

 

DELAY: The response time timer is ON.

 

PASS: Within judgment standard

 

UFAIL: Upper limit value ≤ Measured value

 

LFAIL: Lower limit value ≥ Measured value

 

ULFAIL: Judgment is not possible (the upper or lower 

limit value exceeds the range)

Example

To query the judgment result (when the judgment result is PASS)

PC> 

:MEASure:COMParator?

ST5520> 

PASS

:MEASure:RESult?

Queries measured value and judgment result.

During a test the measured value and then the judgment result at the time this command is 

received are returned as <measured value> and then <judgment result> in data (<data1>, 

<data2>).

After the test is completed, the measured value and judgment result when the previous test was 

completed are returned.
No command header is included in response.

Syntax

:MEASure:RESult?

Response

<data1>,<data2>

<data1>

Measured value 

“8.5 Data Format Table” (p. 125)

<data2>

Judgment result:  OFF /NOCOMP /DELAY /PASS /UFAIL /LFAIL /

ULFAIL (text data)

Example

To query the measured value and judgment result (when the measured 

value is 123.4 M

Ω

 and the judgment result is PASS)

PC>

:MEASure:RESult?

ST5520>

123.4E+06,PASS

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов