Hioki MR8827 Скачать руководство пользователя страница 230

Страница: 230 / 436

225

11 Waveform Calculation Functions

Waveform Calculation Functions

Waveform calculations can only be used with the Memory function.

A pre-specified calculation equation is applied to acquired waveform data and the calculated results are

displayed as a waveform on the Waveform screen.

Waveform calculation settings are made on the Status screen -

[Wave Calc]

sheet.

To Open the

[Wave Calc]

Sheet

Press this key repeatedly to

display the various sheets.

[Status]

[Wave Calc]

[Num Calc]

[Memory Div]

Operations Available From the [Wave Calc] Sheet

Waveform Calculations

•Four Arithmetic Operators ( +, -, *, / )

•Absolute Value (ABS)

•Exponent (EXP)

•Common Logarithm (LOG)

•

Square Root (SQR)

•Moving Average (MOV)

•Parallel displacement along the

time axis

•Differential Calculus: 1st derivative

(DIF), 2nd derivative (DIF2)

•Integral Calculus: 1st integral

(INT), 2nd integral (INT2)

•Trigonometric functions (SIN, COS

TAN)

•Inverse Trigonometric functions

(ASIN, ACOS ATAN)

•

MR8990 Digital Voltmeter Unit

PLC delay shift (PLCS)

(12 types in total)

•

Specified calculation between AB

cursors

Waveform calculations can be

limited to data within the range

specified by AB cursors.

Calculation operator details:

“11.3 Waveform Calculation

Operators and Results” (p. 234)

In addition to the four arithmetic operators, 11 types of functions can be used. It is possible to set up to 16

calculation formulas.

When Scaling is enabled, numerical calculations are performed on scaled values.

aveform Calculation Functions

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды