Hioki MR8827 Скачать руководство пользователя страница 217

Страница: 217 / 436

212

Numerical Value Calculation Settings

10.2 Numerical Value Calculation Settings

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Num Calc]

sheet.

Enable the Numerical Calculation function.

Move the cursor to

[Numerical Calc]

Select

[On]

Specify the waveform calculation range.

Move the cursor to

[Calc Area]

Whole Wave

Applies calculations to the whole waveform.

(Default setting)

A-B Wave

Applies calculations to the data between AB

cursors.

After Trigger

Applies calculations to the waveform after trigger.

Refer to “7.2 Specify a Waveform Range (AB Cursor)” (p. 125).

Choose calculation settings.

Calculation No.

(5)

Phenomenon

(1)

Calculation

Type

(2)

Channel for

Calculation

(4)

Statistical

calculation

(3)

Parameters*

Setting choices depend

on the calculation type.

(1)

Select the calculation type.

Move the cursor to the number of the calculation type for which

you want to choose settings. Select the calculation type.

(When

[List]

is selected, a list of calculation types appears. To

clear the display, press the

TRIG.SET

key.)

Select [Judge] if you require

judgment of calculation results.

(p. 216)

Off

No calculation.

(Default setting)

Area

Area enclosed by zero position and signal

waveform

Average

Average valu

ｘ

e of waveform data

X-Y Area

Area of X-Y composite waveform

Rms

RMS value of waveform data

Time to Lev*

Time from trigger to specified level

Peak-Peak

Peak-to-peak value of waveform data

Lev-time

Measurement value at a specified time point after

triggering

Maximum

Maximum value of waveform data

Max-Time

Time from trigger to maximum value

Pulse Width*

Pulse width of waveform data

Minimum

Minimum value of waveform data

Duty Ratio*

Duty of waveform data

Min-Time

Time from trigger to minimum value

Pulses*

Pulse count of waveform data

Period*

Period of signal waveform

Calculation

Four arithmetic operations on numerical

calculation results

Frequency*

Frequency of signal waveform

Time Diff*

Time difference between phenomenon A and B.

RiseTime

Rise time of waveform data

Phase Diff*

Time difference between phenomenon A and B

displayed as a phase differnce.

FallTime

Fall time of waveform data

High Level

High level value for waveform data

Std Dev

Standard deviation of waveform data

Low Level

Low level value for waveform data

*: This setting can also be made for logic channels

When selecting

[A-B Wave]

, specify

the calculation range using the AB

cursors on the Waveform screen.

If no measurement data has been

acquired by the instrument, first

measure once so that the range

can be specified for calculations

to be applied to subsequent

measurements.

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды