Hioki MR8827 Скачать руководство пользователя страница 182

Страница: 182 / 436

177

Detailed Settings for Modules

8.10.11 Setting Model MR8791 Pulse Generator Unit

Channels installed with Model MR8791 cannot be measured.

Refer to: “To Open [Each Ch] and Make a Channel Selection” (p. 164)

Mode

Select the type of output.

Pulse

Pulse output (Default settings)

Pattern

Pattern output

Refer to the instruction manual of Models U8793, MR8790, and MR8791 regarding

the detailed settings for pattern output.

• The pattern output can be selected only when used channel is set to 32 ch.

• When the used channels is changed, the pattern data will disappear.

Setting Channels to Use

Refer to: Refer to “8.4 Setting Channels to Use (Extending the Recording Length)”

(p. 150)

Frequency

Sets the frequency for pulse output.

0 Hz to 20000 Hz

Duty

Sets the pulse duty.

0% to 100%

Utility Functions

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды