Hioki MR8827 Скачать руководство пользователя страница 113

Страница: 113 / 436

108

Print Type and Workflow

6.1

Print Type and Workflow

There are three basic types of printing.

Print data automatically

during measurement

Auto-print

When the Memory function* is used,

data is acquired for the recording

length then printed automatically.

When the Recorder function is

used, printing is carried out in real

time along with recording.

When the FFT function is used,

data is printed automatically after

FFT analysis is exited.

In both cases, print contents

are selected before starting

measurement.

For printer output, load recording

paper. For LAN output, prepare the

Model 9333 LAN Communicator.

After installation and connections

are completed, turn power on

Set measurement configuration

[Printer]

sheet

Set

[Auto Print]

[On]

Specify the output destination.

(Memory function, FFT function)

Measurement

Set the print contents

Print

The following can be printed simultaneously:

•Waveform data

•Numeric value calculation results

[Printer]

sheet

Print data in bulk after measurement

by pressing the

PRINT

key

Quick Print

Print content when the

PRINT

key

is pressed

At Waveform screen: Waveform

At File screen: File list

At other screens: List

During waveform printing, the

range specified with

[Print Area]

will be printed.

For printer output, load recording

paper. For LAN output, prepare the

Model 9333 LAN Communicator.

After installation and connections

are completed, turn power on

Set

[Select at print]

[No]

and

specify output destination.

Set the print area

Start and Stop Measurement

Press the

PRINT

key.

Print

During waveform printing,

the following can be

printed:

•

Whole waveforms

•

A-B waveforms

*: When the Roll Mode function is used, printing can be carried out simultaneously with waveform display.

(However, at timebase settings higher than 500 ms/div, the print timing will be slower.)

[Printer]

sheet

Selectively print data after

measurement

Selection Print

(Default setting)

When the

PRINT

key is pressed

at the File screen, content can be

selected before printing. This allows

printing different items each time.

At the File screen, the file list is

printed. At other screens, a list is

printed.

For printer output, load recording

paper. For LAN output, prepare the

Model 9333 LAN Communicator.

After installation and connections

are completed, turn power on

Press the

PRINT

key.

Select the print contents

The following can be printed:

•

Whole waveforms

•

A-B waveforms

•

Post-/Pre-trigger waveforms

•

Lists (Settings List)

•Report

Start and Stop Measurement

Print

Settings window

Set

[Select at print]

[Yes]

and

specify output destination.

When both auto-print and auto-save are enabled, auto-save is executed first.

However, when the Roll Mode function (default setting:

[Auto]

) is used with the Memory function, auto-

print has priority.

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды