Hioki IR4055 Скачать руководство пользователя

Страница: 12 / 82

Operating Precautions

Operating Precautions

Follow these precautions to ensure safe operation and to obtain the

full benefits of the various functions.

DANGER

•

For your safe operation, do not connect any test

lead to the primary of the distribution panel.

•

Do not short-circuit two wires to be measured by

bringing the test leads into contact with them. Arcs

or such graveaccidents are likely to occur.

•

To avoid short circuit or electric shock, do not touch

the metal part of the connecting test lead tip.

•

To avoid electric shock, be careful to avoid shorting

live lines with the test leads tip.

•

If the test lead or the instrument is damaged, there

is a risk of electric shock. Perform the following

inspection before using them:

•

Before using the instrument check that the coating

of the test leads are neither ripped nor torn and that

no metal parts are exposed. Using the instrument

under such conditions could result in electric

shock. Replace the test leads with those specified

by our company.

•

Verify that the instrument operates normally to

ensure that no damage occurred during storage

or shipping. If you find any damage, contact your

authorized Hioki distributor or reseller.

Содержание IR4055



















































































Результаты поиска

Содержание IR4055

Отзывы:

Похожие инструкции для IR4055

Бренды по названию

Популярные бренды

Hioki IR4055, Инструкция по эксплуатации

Результаты поиска

Содержание IR4055

Отзывы:

Похожие инструкции для IR4055

Бренды по названию

Популярные бренды