Hioki IM7580 Скачать руководство пользователя страница 16

Страница: 16 / 340

Operating Precautions

Handling of cords and fixtures

WARNING

Use only the designated power cord with this instrument. Use of other power cords may

cause fire.

CAUTION

•

To avoid damaging the power cord, grasp the plug, not the cord, when

unplugging it from the power outlet.

•

To avoid breaking the cables or probes, do not bend or pull them.

•

Bare conductors may get exposed if the insulation melts. Keep the cables well

away from heat sources.

•

Keep in mind that, in some cases, conductors to be measured may be hot.

•

Use only the specified connection cables. Using a non-specified cable may result in

incorrect measurements due to poor connection or other reasons.

•

Read the instruction manual supplied with the product to be used before using a fixture.

Before connecting to the EXT I/O terminals

WARNING

To avoid electric shock or damage to the equipment, always observe the following

precautions when connecting to the EXT I/O connector.

•

Always turn off the power to the instrument and to any devices to be connected

before making connections.

•

Be careful to avoid exceeding the ratings of EXT I/O connector. (p. 212)

•

During operation, a wire becoming dislocated and contacting another

conductive object can be serious hazard. Use screws to secure the EXT I/O

connectors.

•

Ensure that devices and systems to be connected to the EXT I/O terminals are

properly isolated.

•

ISO_5V pin of the EXT I/O connector is a 5V power output. Do not apply external

power to this pin.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды