manualshive.com logo in svg

Hioki IM7580, Инструкция по эксплуатации

Поделиться
Скачать
Hioki IM7580 Скачать руководство пользователя страница 151

143

Calibration

5.2  Calibration

5.2.1 

Setting the Calibration [CAL]

The errors between the measurement instrument and the calibration reference surface are 

eliminated.

Connect the three types of standard units (open/short/load) one by one with the reference surface 

(terminal) to be calibrated, and obtain respective measurements.

In case of DC resistance measurements, if different standard units are used, perform AC 

measurement and DC measurement separately.

To avoid improper connection of the three types of standard units (open/short/load), judgment can 

be made by setting the limit with DC measurement.

See “Prevention of improper standard unit connection” (p. 150).

When calibration is performed with the terminal connected to the test sample, electric length 

compensation, open compensation, and short compensation are not necessary.

1

2

1 

 Press 

[ADJUST]

.

2 

 Press 

[CAL]

.

3

4

3 

 Press 

[MODE]

.

4 

 Selects the calibration method.

[OFF]

Calibration is not performed.

[SPOT]

Acquires the compensation values at the 

set measurement frequencies.

LCR mode: Measurement frequencies can 

be set for up to five points.

ANALYZER mode: Linked to the sweep 

points (MAX 801 points).

[ALL]

Acquires all the calibration of measurement 

frequencies (LCR mode) in a batch.

5

5 

 Press 

[DELAY]

.

Go to the next page.

5

Calibration and Compensation

Содержание IM7580





















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды