manualshive.com logo in svg

Hioki IM7580, Инструкция по эксплуатации

Поделиться
Скачать
Hioki IM7580 Скачать руководство пользователя страница 121

113

Judging Measurement Results (Comparator Function)

4

5

6

4 

 Select the judgment mode.

[OFF]

Disables comparator function.

[AREA]

Enables area judgment. (p. 116)

[PEAK]

Enables peak judgment. (p. 120)

5 

 When a measured value is outside the guaranteed 

accuracy range, set how the measured value is 

judged.

[DO]

Judges when a measured value is outside 

the guaranteed accuracy range.

[NOT]

Outputs error for HI judgment when a 

measured value is outside the guaranteed 

accuracy range.

6 

 Sets the beep sounds for judgment results.

[OFF]

No beep sound.

[IN]

Beeps if all the judgment results are IN.

[NG]

Beeps if one of the judgment results is LO 

or HI.

7

8

9

7 

 With 

/

, set the beep tone.

Settable range 0 to 14

8 

 With 

/

, set the beep volume.

Settable range 1 to 3

9 

 Press 

[EXIT]

 to close the judgment settings 

screen.

10 

 Press 

[EXIT]

 to close the advanced settings 

screen.

4.8.2 

Setting the Parameter to be Judged

1

3

2

1 

 Press 

[SETUP]

.

2 

 Press 

[COMP]

 tab.

3 

 Press 

[PARA]

.

4

Analyzer Function

Содержание IM7580





















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды