Hioki IM7580 Скачать руководство пользователя страница 11

Страница: 11 / 340

Safety Information

Safety Information

This instrument is designed to conform to IEC 61010 Safety Standards, and has been thoroughly tested

for safety prior to shipment. However, using the instrument in a way not described in this manual may

negate the provided safety features.

Before using the instrument, be certain to carefully read the following safety notes.

DANGER

Mishandling during use could result in injury or death, as well as damage to the

instrument. Be certain that you understand the instructions and precautions in

the manual before use.

WARNING

With regard to the electricity supply, there are risks of electric shock, heat

generation, fire, and arc discharge due to short circuits. If persons unfamiliar

with electricity measuring instrument are to use the instrument, another person

familiar with such instruments must supervise operations.

Notation

In this manual, the risk seriousness and the hazard levels are classified as follows.

DANGER

Indicates an imminently hazardous situation that will result in death or serious injury to

the operator.

WARNING

Indicates a potentially hazardous situation that may result in death or serious injury to

the operator.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury

to the operator or damage to the instrument or malfunction.

IMPORTANT

Indicates information related to the operation of the instrument or maintenance tasks

with which the operators must be fully familiar.
Indicates a high voltage hazard.

If a particular safety check is not performed or the instrument is mishandled, this may

give rise to a hazardous situation; the operator may receive an electric shock, may get

burnt or may even be fatally injured.

Indicates prohibited actions.

Indicates the action which must be performed.

Additional information is explained below.

Appx.

Ind.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды