Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 137

background image

25

Once fulfilled the AUTO-STABILIZATION procedure
till the OK, all the outriggers touch the ground and

machine is levelled, then, placing the remote
control on its basket support the display will show

the “MACHINE STABILIZED” icon

on position n.5

and aerial part movements will be allowed.

LL15.70 is able to stabilize on a surface up to 15° of inclination, in case of the
surface exceed that limit machine will not allow to start the stabilization

procedure and display will show the MAXIMUM TILT ANGLE EXCEEDED icon.

NOTE: During the intermediate steps of auto-stabilization and outriggers auto-
retraction, while two or three outriggers are touching the ground, the engine
automatically runs at minimum rpm to ensure smooth movements.

NOTE: If pedal option is active the

“MACHINE STABILIZED“ icon

appears after

pedal have been pressed to enable the aerial part movements.

4.2.2 OUTRIGGERS AUTO-RETRACTION

To be able to automatically retract the outriggers the machine must be closed

and aligned, to automatically retract the outriggers it has to be kept pressed
remote control button n.1

“

OUTRIGGERS AUTOMATIC RETRACTION

”.

“MAXIMUM TILT ANGLE EXCEED”

ICON

“MACHINE

STABILIZED”

ICON

AUTOSTAB
WAIT

ST1 GND
ST2 NO GND

ST3 NO GND
ST4 NO GND

AUTS
STEP: 2

OK

AUTOSTAB

WAIT

ST1 NO GND

ST2 NO GND
ST3 NO GND

ST4 NO GND

AUTS
STEP: 1

AUTOSTAB

WAIT

ST1 GND
ST2 GND

ST3 GND

ST4 GND

AUTS
STEP: 49

«
...
23
24
25
26
27
...
»

Содержание LightLift 15.70 3S










































































































































Отзывы:

Нет отзывов

Похожие инструкции для LightLift 15.70 3S

Бренд: Badger Meter Страницы: 48

Бренд: Miller Страницы: 16

Бренд: WeldKing Страницы: 31

Бренд: Patlite Страницы: 38

Бренд: ICP DAS USA Страницы: 156

Бренд: R-Tech Страницы: 19

Бренд: WAGO Страницы: 20

ARCITECH WS2100

Бренд: Campbell Hausfeld Страницы: 36

Бренд: Logic Страницы: 3

Бренд: Ravaglioli Страницы: 98

Бренд: Infinity Страницы: 24

Бренд: Telpro Страницы: 6

Бренд: Greenheck Страницы: 16

Бренд: Elektra Beckum Страницы: 52

Бренд: BorMann Страницы: 33

Бренд: Thermal Dynamics Страницы: 144

Бренд: Palfinger Страницы: 76

Бренд: R-Tech Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды