background image

DEF SCR SYSTEM (DCU)

5–114

DTC: P203D

EN01H16F02040F03001026

DTC: P203D DEF tank level sensor - out of range (Out of range high)

INFORMATION

1. Technical description

The DEF tank level sensor is connected via the engine ECU and DCU through CAN communication, and it sends and
receives data.

<Description of malfunction>

Failure of DEF tank level sensor is received from CAN data.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.

(2) Judgement criteria

Failure of DEF tank level sensor (High failure flag) is received from CAN data.

3. Reset condition

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

MIL: ON

DEF level indicator is stopped.

Common rail_CAN_J/C3

Common rail_CAN_J/C1

NOx 

sensor 1

NOx 

sensor 2

%JU

%JZ

%JQ

%KF

%JV

(CA2H)

(CA2L)

(CA2H)

(CA2L)

(CA3H)

%KH

%KG

(CA3L)

(CA3H)

%KE
(CA3L)

%KM

(CA3H)

%KL

(CA3L)

%JR

(CA2H)

%JW

(CA2L)

LE9

LE8

(CANH)

(CANL)

H

L

H

L

H

L

%JS

(CA2H)

%JX

(CA2L)

LED

LEC

(CANH)

(CANL)

DEF sensor 

(DEF tank

level sensor)

H

L

%KP

(CA3H)

%KN

(CA3L)

LEK

LEJ

(CANH)

(CANL)

H

L

&RE
(CA2H)

&RJ
(CA2L)

&RD

(CA2H)

&RH

(CA2L)

&RF

&RK

(CA2H)

(CA2L)

Common rail_ 

CAN_J/C2

Engine

ECU

DCU

#S5

#S7

#S5

#S7

#AW

#AV

#AW

#AV

LCM

H

L

(CA1H)

LCN

LF5

LF6

(CA1L)

(CAL1)

#CP #CP

#CQ

#CQ

#SD #SD

#SF

#SF

K6V

(CANH)

K6W

(CANL)

H

L

(CAH1)

LEY

LEZ

250K

500K

(CAL0)

(CAH0)

LJM

LJN

(CAH1)

(CAL1)

LJK

LJL

(CAH0)

(CAL0)

BCU

SAPH16F020400075

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы: