Hino 238 Скачать руководство пользователя страница 575 | Manualshive

Страница: 575 / 919

background image

DEF SCR SYSTEM (DCU)

5–9

SIGNAL CHECK HARNESS

EN01H16F02040F03001006

1.

MENTION OF THE SIGNAL CHECK HARNESS

(1)

HINO provides a signal check harness to check the DCU.

! CAUTION

•

To prevent damage of the DCU connector, connect the signal
check harness and perform measuring by bringing the test
probe into contact with the signal check harness side.

INSPECTION

EN01H16F02040F03001007

MALFUNCTION INDICATOR LIGHT STATUS

1.

INSPECTION PROCEDURE

(1)

Set the starter switch to the "ON" position (Do not start the
engine) and confirm that the MIL (malfunction indicator light) in
the indicator area light up.
If the DTC of P204F appears during meter multi-display, have the
BCU communicate with the Hino-DX and check the detailed DTC.

HINT

•

If the MIL (Malfunction Indicator Light) is lit, perform a sys-
tem check to see if the malfunction is of the past or present.

•

In the case of the past malfunction, this light will turn off if a
status is judged to be normal in 3 times of driving.

•

DTC must be cleared on the Hino-DX, after MIL comes off.

(Definition of 1 time of driving)
a.

Begins with engine start and ends with engine shut off.

b.

Begins with engine start and ends after four hours of continu-
ous engine-on operation.

c.

Begins at end of the previous four hours of continuous engine
on operation and ends after four hours of continuous engine-
on operation.

d.

Begins at the end of the previous four hours of continuous
engine-on operation and ends with engine shut off.

•

Since the normal judgment method and time differ according to
the malfunction code, a proper definition will be selected from the
above 4 definitions.

•

If the MIL (malfunction indicator light) does not go out, the system
is abnormal. Check the system according to diagnosis on the fol-
lowing page.

09843-E9030

SAPH16F020400008

SAPH16F020400009

«
...
573
574
575
576
577
...
»

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

Бренд: Camcar Страницы: 2

Бренд: Wagan Страницы: 12

V2 SUPERCHARGER

Бренд: Tesla Страницы: 9

MOLLE PANELS RAM 2500

Бренд: PUTCO Страницы: 4

Бренд: Westfalia Страницы: 18

Бренд: Subaru Страницы: 34

Бренд: Sirius Satellite Radio Страницы: 8

2007 MazdaSpeed6

Бренд: Mazda Страницы: 12

PACCAR PACMOBILE 20

Бренд: DAF Страницы: 18

Бренд: Whispbar Страницы: 14

Бренд: Chevrolet Страницы: 412

Бренд: Voxoa Страницы: 48

Бренд: RBO Страницы: 15

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Бренд: Havis-Shields Страницы: 1

Бренд: Caraudio-Systems Страницы: 9

Бренд: Oldsmobile Страницы: 358

Бренд: Mazda Страницы: 1001

Бренд: Sintrones Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды