manualshive.com logo in svg

Hiniker 1852, Руководство оператора, Страница: 14 / 31

Поделиться
Скачать
Hiniker 1852 Скачать руководство пользователя страница 14

PLOW ASSEMBLY

GENERAL INFORMATION

WARNING: To prevent personal injury 

or  death,  be  certain  to  keep  clear  of 

any parts that may drop when remov-

ing bundling straps, wires or brackets. Sup-

port heavy sections with hoist or blocks be-

fore removing wires or straps.

In  the  following  instructions,  left  and  right  ma-

chine  references  are  defined  as  being  viewed 

from the cab of the truck.

Be  certain  that  hydraulic  hoses  and  electrical 

wires are safely routed and allow full motion of 

moving parts. Secure loose wires with plastic tie 

straps.

Some components are fastened at incorrect lo-

cations for shipping purposes.

All  hardware  should  be  tightened  only  enough 

to ensure safety during assembly. Torque hard-

ware  to  specified  values,  as  shown  in  the  fol-

lowing chart, only after assembly has been com-

pleted.

GRADE 5 TYPE B & F LOCK NUT TORQUES

Size

Ft-lbs.

N-m

5/16”

13-18

17-25

3/8”

23-33

31-44

1/2”

58-82

79-112

5/8”

117-165

158-223

GRADE 5 BOLT TORQUES*

Size

Ft-lbs.

N-m

1/4”

8-12

11-16

3/8”

29-41

39-56

1/2”

73-103

99-140

5/8”

146-206

198-279

* applications without lock nuts
Replace  worn  bolts  and  lock  nuts  with                 

grade 5 bolts and equivalent type B and type F 

lock nuts. Type B lock nuts are plain hex; type F 

lock nuts are flanged hex.

PLOW ASSEMBLY

1.  Lift  the  snowplow  moldboard  assembly  to  a 

clear level working area by hooking hoist chains 

through the two holes in the top plate of the cen-

ter mast. The hoist should be capable of lifting at 

least 1,000 lb. loads.

 

Remove two side markers and 5/16 inch hard-

ware  from  the  top  of  the  moldboard,  and  set 

aside for assembly later. Save two sets of 5/16 

inch hex bolts, flat washers and lock nuts from 

the  shipping  brackets  for  assembling  the  side 

markers.

 

Do not remove shipping straps from wing cylin-

ders at this time.

2.  Open the frame crate and set aside the power 

unit box, headlamp boxes and parts boxes for 

later  assembly.  Remove  the  frame  assembly 

from the shipping crate to a piece of cardboard 

or  other  padding  that will  prevent  scratches  in 

the paint.

 

Locate  the  3/4  inch  x  4-1/4  inch  hex  bolt,  3/4 

inch nylon insert lock nut and one 90O O-ring/

flare hydraulic fitting in the hardware bag in the 

parts box.

 

Install the O-ring end of the 90O fitting into the 

lift cylinder port so that the flared end points to-

ward the rod end when tightened.

 

Swing the lift frame up to its approximate work-

ing position and hold with a hoist or forklift. 

 

 

Bolt the upper lift links to the outside of the two 

lugs  on  the  lift  frame,  then  pin  the  lower  end 

of the lift cylinder between the two lugs on the 

frame assembly with the hardware provided.

DWG NO. 4169A

12 V-Plow Assembly

Содержание 1852
































Отзывы:

Нет отзывов