HIMA HIMax X-SB 01 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 38

HIMA HIMax X-SB 01 Скачать руководство пользователя страница 24

4 Start-up

X-SB 01

Page 24 of 38

HI 801 007 E Rev. 4.00

4.3

Configuring the Module in SILworX

The module is configured in the Hardware Editor of the SILworX programming tool.

The following tables present the statuses and parameters for the module in the same order
given in the SILworX Hardware Editor.

4.3.1 Tab:

Module

The

Module

tab contains the statuses and parameters for the module.

System parameter

Description

Name Module

name

IP Address

IP address of the Ethernet interface.

Subnet Mask

Subnet mask of the Ethernet interface

Speed Mode

Transfer rate:

10

Mbit/s

100

Mbit/s

Autoneg

HIMA recommends to maintain the

Autoneg

default setting.

Flow Control Mode

Operational mode of the flow control:

Half

Duplex

Full

Duplex

Autoneg

HIMA recommends to maintain the

Autoneg

default setting.

Standard Interface

Activated: the interface is used as standard interface for the system
login.
Deactivated: the interface is not used as standard interface for the
system login.
Default setting: Deactivated

Default Gateway

IP address of the default gateway.

ARP Aging Time [s]

A system bus module stores the MAC addresses of the
communication partners in a MAC/IP address assignment table
(ARP cache).
If in a period of 1x....2x

ARP Aging Time

...

... messages of the communication are received, the MAC

address remains stored in the ARP cache.

... no messages of the communication partner are received, the

MAC address is erased from the ARP cache.

The typical value for the

ARP Aging Time

in a local network ranges

from 5...300 s.
The user cannot read the contents of the ARP cache.

Range of values: 1...3600 s
Default value: 60 s

Note:

If routers or gateways are used, the user must adjust (increase) the

ARP Aging Time

due to the additional time required for two-way

transmission.
If the

ARP Aging Time

is too low, the MAC address of the

communication partner is erased from the ARP cache, the
communication is delayed or interrupted

.

For an efficient

performance, the ARP aging time value must be less than the
receive timeout set for the protocols in use.

«
...
22
23
24
25
26
...
»

Содержание HIMax X-SB 01







































Отзывы:

Нет отзывов