manualshive.com logo in svg

HIMA HIMatrix, Руководство пользователя, Страница: 25 / 38

Поделиться
Скачать
HIMA HIMatrix Скачать руководство пользователя страница 25

AI 8 01 

4 Start-up 

HI 800 195 E Rev. 2.00 

Page 25 of 38 

4.4.3 

Analog Inputs 

System signal 

R/W 

Description 

Mod.SRS [UDINT] 

R 

Slot number (System.Rack.Slot) 

Mod. Type [UINT] 

R 

Type of module, target value: 0xFD02 [64 770

dec

] 

Mod. Error Code 
[WORD] 

R 

Error codes for the module 

Coding 

Description 

0x0000 

I/O processing, if required with errors 
see other error codes 

0x0001 

No I/O processing (CPU not in RUN)  

0x0002 

No I/O processing during the booting test 

0x0004 

Manufacturer interface operating 

0x0010 

No I/O processing: invalid configuration 

0x0020 

No I/O processing: fault rate exceeded 

0x0040/ 
0x0080 

No I/O processing: configured module not plugged in 

 

AI.Error Code 
[WORD] 

R 

Error codes for all analog inputs 

Coding 

Description 

0x0001 Module 

fault 

0x0008 

FTT test: Walking bit of data bus faulty 

0x0010 

FTT test: Error while checking coefficients 

0x0020 

FTT test: Operating voltages faulty 

0x0040 

A/D conversion faulty (DRDY_LOW) 

0x0080 

Cross links of MUX faulty 

0x0100 

Walking bit of data bus faulty 

0x0200 

Multiplexer addresses faulty 

0x0400 

Faulty operating voltages 

0x0800 

Measuring system (characteristic) faulty (unipolar) 

0x1000 

Measuring system (final values, zero point) faulty 
(unipolar) 

0x2000 

Measuring system (characteristic) faulty (bipolar) 

0x4000 

Measuring system (final values, zero point) faulty (bipolar) 

0x8000 

A/D conversion faulty (DRDY_HIGH) 

 

AI[0x].Error Code 
[BYTE] 

R 

Error codes for the analog input channels 

Coding 

Description 

0x01 

Fault in the analog input module 

0x02 

CPU operating system versions prior to 4: measured 
values invalid, 
CPU operating system version 4 and higher: not used 

0x04 

A/D converter faulty, 
CPU operating system version 4 and higher: measured 
values invalid 

0x08 

Measured value out of the safety-related accuracy 

0x10 

Measured value overflow 

0x20 Channel 

not 

operating 

0x40 

Address error of both A/D converters 

 

AI[0x].Value [INT] 

R 

  Analog value of each channel 

INT

 from -1000...+1000  (device version: 

FS1000), voltage range: -10...+10 V 

  Analog value of each channel 

INT

 from -2000...+2000  (device version: 

FS2000), voltage range: -10...+10 V 

The validity depends on the AI[0x].Error code 

Содержание HIMatrix







































Отзывы:

Нет отзывов