PETROL SAW
SAFETY SHEET
(Hilti DSH 900-X)
PLEASE READ THIS GUIDE CAREFULLY
BEFORE OPERATING THE EQUIPMENT
IMPORTANT - CONDUCT A RISK ASSESSMENT
Before you commence any work at your chosen work area, you should
undertake some preliminary hazard identification and risk control
precautions. Ideally more than one person should do this. This is
undertaken by:
1. Physically inspecting the work site
2. Reviewing the best way/job steps required to complete the task
3. Reviewing the Safe Work Information supplied with the equipment
4. Reviewing other reference documentation and expert advice.
The hazard identification and control process steps are defined as:
1. Identify the Hazards (eg. 240V power drill use around wet areas)
2. Assess the Risk (multi earth paths - possible electrocution)
3. Select the Control Measure (e.g. dry the area; use an RCD; use a
cordless drill etc)
4. Re-assess the Risk (risk of electrocution now negligible). This is
undertaken to ensure that the risk control measures adopted have not
introduced any new risks to the work area.
HELP AND SUPPORT
If the unit does not operate correctly or you are unhappy with its
performance, return it to Asset Construction Hire for an exchange,
or phone for assistance. Do not attempt repairs yourself.
Asset Construction Hire
Phone:1300 361 383 or email: [email protected]
OPERATION MANUAL
A PDF of the full Operation Manual is available at:
www.assethire.com.au/manuals-specs-safety-sheets/
and must be read before using the equipment.
BEFORE OPERATING THE EQUIPMENT:
•
Read this Safety Sheet and any other information provided with the
equipment, including instructions, decals and operation guidelines.
•
Check that you understand how and when the use the equipment,
and know how to operate it safely.
•
Ensure that it is only used according to the manufacturers and hirer’s
instructions, and only for work that is compatable with its technical
limitations.
•
Operate in a clear work area free from nonessential persons, children,
animals or hazards.
•
Ensure that you have a secure footing and clear access and egress to
the work area while on the job.
•
Do not operate any equipment if you are tired or suffering any medical
condition, or if under the influence of drugs or alcohol which may
cause lethargy or dangers to yourself or others.
•
Do not use faulty equipment. If in doubt contact Asset Construction Hire.
SAFETY INFORMATION
•
Always hold the tool firmly with both hands on the grips provided.
Keep the grips dry, clean and freefrom oil and grease.
•
Never use the tool without the guard (hood). Adjust the guard to the
correct position. The guard must be securely attached and positioned
for maximum safety, so that the smallest possible part of the cutting
disc is exposed to the operator. Make sure that sparks created during
use do not present a hazard. The guard helps to protect the operator
from broken disc fragments, inadvertent contact with the cutting disc
and uncontrolled flying sparks.
•
Do not touch rotating parts – risk of injury!
•
Maintain a firm footing and balance at all times. This will allow you to
control the tool better, even in unexpected situations. Avoid unusual
postures.
•
Wear suitable work clothes. Do not wear jewelry or loose clothing.
Keep your hair, clothing and gloves away from moving parts. Loose
clothes, jewelry or long hair can be snagged by moving parts. Wear
eye protection. Flying fragments present a risk of injury to the body
and eyes.
•
If the tool or the cutting disc has been dropped or has fallen, check
the tool and the cutting disc for damage. Change the cutting disc if
necessary.
•
Switch the tool off before adjusting the guard or changing the cutting
disc. Switch the tool off after use. Wear protective gloves also when
changing the cutting disc. Touching the cutting disc presents a risk of
injury (cuts or burns).
•
Use of the wet cutting method is preferable in order to reduce the
amount of dust produced when cutting mineral materials and asphalt.
•
Avoid skin contact with the slurry created when using the wet cutting
method.
•
Dust from materials such as paint containing lead, some types of
wood, minerals and metal can be harmful to health. Contact with or
inhalation of the dust can cause allergic reactions and/or respiratory
or other diseases to the operator or bystanders. To reduce the
amount of dust produced when cutting, we recommend use of the wet
cutting method. Make sure that the workplace is well ventilated. It is
advisable to wear a filter class P2 dust mask. Comply with national
regulations applicable to the materials you will be working with.
Cutting material containing asbestos is not permissible.
•
Take breaks between working and do relaxation and finger exercises
to improve the blood circulation in your fingers. Exposure to vibration
during long periods of work can lead to disorders of the blood vessels
and nervous system in the fingers, hands and wrists.
•
Consult the responsible structural engineer, architect or person in
charge of the building project before starting work. Slits cut into
load-bearing walls or other structures can influence the statics
of the structure, especially when reinforcing bars or load-bearing
components are cut.
•
If the work involves breaking through, always secure the area on the
side opposite to where the work is being carried out. Pieces of debris
could drop out and/or fall down and injure other persons.
•
Never leave the tool running while unattended. Switch the engine off
and wait until the cutting disc has come to a complete standstill before
placing the tool on the ground or before transporting it.
•
Make sure that the pump cover is installed if you operate the tool
without an external water pump.
PERSONAL PROTECTION EQUIPMENT (PPE)
PROTECTIVE
GLOVES
HEARING
PROTECTION
HIGH VIS
JACKET
RESPIRATORY
PROTECTION
PROTECTIVE
HELMET
PROTECTIVE
BOOTS
