hilscher NANL-B500G-RE Скачать руководство пользователя | Manualshive

Страница: 49 / 90

background image

Commissioning

49/90

7.5

Autonomous operating mode, capturing on USB memory
device

7.5.1

Full capturing process (Live-Dump-Mode)

Proceed as follows if you want to use the analyzer device NANL-B500G-RE
in the Autonomous operating mode

in Live dump mode

with an USB

memroy device and want to record data during the entire time span of an
analysis process:

Step 1: Safety precautions

Device Destruction

Ø

The voltage applied at the NANL-B500G-RE device must not exceed 30
V, otherwise the device may be destroyed.

Ø

At the I/O signal pins of the external IO interface use exclusively 3.3 V
or 24 V signaling voltage. Higher signaling voltages lead to severe
damage to the NANL-B500G-RE device!

Step 2: Connect the device to USB, use the autonomous operating
mode

in "live dump mode"

and transfer evaluation data to a PC

Ø

Connect the analyzer device NANL-B500G-RE to an

external 24V

power supply

.

Ø

Connect the USB memory device (USB stick or USB hard disk with at
least 100 MByte capacity) to the USB socket on the reverse side of the
NANL-B500G-RE analyzer device.

Ø

When using an USB device with a power consumption of more than 500
mA, connect a separate power supply; If required, it is also possible to
feed it via an USB hub.

Ê

The analyzer device NANL-B500G-RE displays the autonomous
operating mode (live dump mode) as a particular LED state (STA0-LED/
orange/On, refer to section

SYS, STA0, STA1, I/O, LINK and RX (Front

Ø

To start capturing, briefly press the red REC button on the front side of
the device.

Note:

If when switching on the analyzer device NANL-B500G-RE an USB
memory device with a partition marked as "bootable" is connected
to the analyzer device NANL-B500G-RE, the netANALYZER device
may not start correctly (SYS LED is yellow).

Ê

The analyzer device NANL-B500G-RE starts capturing the data traffic
in .pcap files, which are stored in the root directory of the USB memory
device.

Ø

To stop capturing, press the red REC button on the front side of the
device for at least 1 second.

netANALYZER device NANL-B500G-RE | Installation, operation and hardware description
DOC091110UM26EN | Revision 26 | English | 2019-07 | Released | Public

© Hilscher 2007-2019

«
...
47
48
49
50
51
...
»

Содержание NANL-B500G-RE



























































































Отзывы:

Нет отзывов

Похожие инструкции для NANL-B500G-RE

TUNICS T100S-HP

Бренд: Yenista Optics Страницы: 66

Бренд: Garmin Страницы: 120

Бренд: HANYOUNGNUX Страницы: 4

Бренд: VELOCICALC Страницы: 10

Бренд: P3 International Страницы: 1

Бренд: NCS Страницы: 7

Бренд: Ferret Страницы: 18

Бренд: UNI-T Страницы: 2

Бренд: Laserworld Страницы: 5

Бренд: XS Instruments Страницы: 41

Бренд: SEFRAM Страницы: 31

Бренд: Polimaster Страницы: 24

Бренд: Ocean Reef Страницы: 24

Бренд: Allen Organ Company Страницы: 29

Бренд: dacell Страницы: 39

Бренд: Sonel Страницы: 56

Privia PX-860BK

Бренд: Casio Страницы: 67

Бренд: HOKUYO AUTOMATIC Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды