hilscher NANL-B500G-RE Скачать руководство пользователя

Страница: 35 / 90

Commissioning

35/90

Commissioning

In order to install and commission the NANL-B500G-RE device, you must
proceed as described in the following sections.

For installation and operation of the netANALYZER device check
any notes in the overview in chapter

7.1

Check firewall settings

What

Description

Problem

NANL-B500G-RE does not work with active firewall software.

Question

My firewall seems to block communication with netANALYZER. What do I
have to consider in my firewall rule set?

Workaround

If your firewall is blocking TCP or UDP communication you have to
consider the NANL-B500G-RE TCP/IP and UDP/IP communication
behaviour in your firewall rule set or disable your firewall temporarily while
working with the netANALYZER.

Table 15: Workarround if firewall blocks communication

Figure 7: Firewall settings

Содержание NANL-B500G-RE



























































































Результаты поиска

Содержание NANL-B500G-RE

Отзывы:

Похожие инструкции для NANL-B500G-RE

Бренды по названию

Популярные бренды

hilscher NANL-B500G-RE, Руководство пользователя

Результаты поиска

Содержание NANL-B500G-RE

Отзывы:

Похожие инструкции для NANL-B500G-RE

Бренды по названию

Популярные бренды