hilscher 1912.112 Скачать руководство пользователя страница 132

Страница: 132 / 154

Technical data

132/154

12.2 Technical data IO-Link Wireless Master

Parameter

Value

Tracks and IO-Link Devices

2 wireless tracks for up to 16 IO-Link Devices

Radio frequencies

RFch (RF channel center frequency): 2403 … 2478 MHz (wireless channels 3 – 78,
configurable).

The IO-Link Wireless Master uses the frequencies (wireless channels) 2401 (1), 2402 (2),
2479 (79), 2480 (80) for network configurations purposes and cannot be configured for
communication purposes.

Range of the wireless
function

Max. 10 m distance

Masters per cell

Max. 3 masters within a circle of 20 m diameter

Antennas

3 SMA antennas

Table 97: Technical data IO-Link Wireless Master

Содержание 1912.112



























































































































































Результаты поиска

Содержание 1912.112

Отзывы:

Похожие инструкции для 1912.112

Бренды по названию

Популярные бренды

hilscher 1912.112, Руководство пользователя

Результаты поиска

Содержание 1912.112

Отзывы:

Похожие инструкции для 1912.112

Бренды по названию

Популярные бренды