Hillyard TRIDENT R26SC PRO, Руководство по эксплуатации и обслуживанию

Страница: 26 / 84

ENGLISH
REPLACING THE BRUSH HEAD SPLASH GUARD
If the splash guard rubber blades of the brush head side casing are damaged they cannot work properly, namely they cannot convey the dirty detergent solution towards the squeegee, therefore the splash guard
rubber blades need to be checked. To replace the brush head splash guards, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal objects.
3. Stand on the left side of the machine.
4. Remove the left splash guard (1), unscrew the knobs (2) on the brush head body ( Fig.1 ).
5. Remove the rear rubber blade compression plate (3), and release the stopper (4) on rubber blade compression plate ( Fig.2 ).
6. Remove the splash guards (5) from the left splash guard body and replace it with a new one or else turn it around ( Fig.3 ).
7. Repeat the operations in reverse order to reassemble all the parts.
8. Repeat the operations just carried out also for the right side casing as well.
1 2 3
2
3
1
4
5
N.B. : Before using the machine, remember to adjust the squeegee body: see the section titled “ ADJUSTING THE SQUEEGEE BODY'S RUBBER BLADES ”.
N.B. : It is recommended to replace both squeegee body blades in order to ensure good results when drying the floor.
6
6
3
3
5 4
4 5
2 1
1 2
ADJUSTMENT INTERVENTIONS
ADJUSTING THE SQUEEGEE BODY'S RUBBER BLADES
The careful adjustment of the squeegee body rubber blades guarantees better cleaning of the floor.
To adjust the squeegee body blades, proceed as follows:
1. Sit on the driver’s seat.
2. Insert the key (1) into the main switch on the control panel. Set the main switch to "I" ( Fig.1 ).
3. Lower the brush head body and press the “BRUSH HEAD CONTROL” button (2) on the control panel ( Fig.2 ).
N.B. : as soon as the button (2) on the control panel is pressed, the green LED (3) (“BRUSH HEAD BODY WORK POSITION”) will switch on ( Fig.2 ).
4. Lower the squeegee body and press the “SQUEEGEE CONTROL” button (4) on the control panel ( Fig.2 ).
N.B. : as soon as the button (4) on the control panel is pressed, the green LED (5) (“SQUEEGEE BODY WORK POSITION”) will switch on ( Fig.2 ).
5. Press the drive pedal (6) ( Fig.3 ) to begin moving the machine.
6. As soon as the brush head and the squeegee have reached their working positions, perform the procedure for securing the machine (see the section titled “ SECURING THE MACHINE ”).
ATTENTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal objects.
7. Stand at the back of the machine.
Adjusting the height of the squeegee body:
8. Adjust the height of the rubber blade in relation to the floor by loosening or tightening the knobs (7) ( Fig.4 ).
NB : Figure 4 indicates the direction of rotation for decreasing the distance between the squeegee support and the floor. This distance can be increased by turning it in the opposite direction.
NB : By decreasing the distance between the squeegee support and the floor, the rubber blades present in the squeegee's body move closer to the floor.
N.B. : the right-hand and left-hand knobs must be rotated the same number of times, so that the squeegee is parallel to the floor when it is working.
N.B. : Check for proper adjustment by looking at the instrument (8) positioned on the squeegee body ( Fig.5 ).
Adjusting the tilt of the squeegee body:
9. To adjust the inclination of the squeegee body rubber blades with respect to the floor, tighten or loosen the knob (9) ( Fig.6 ), until the squeegee body rubber blades are bent towards the outside evenly along
the entire length by about 30° with respect to the floor.
3 1
1
6
2
5
3
4
2
5 4
7
8
26