Hillstone SG-6000-X7180 Скачать руководство пользователя страница 29

Страница: 29 / 64

Chapter 2 Installation Preparation

Hillstone

Hillstone SG-6000 X-Series Hardware Reference Guide

Chapter 2 Installation Preparation

Overview

To prevent personnel injury and equipment damage, please carefully read all the
requirements and cautions in this chapter before the installation.

This chapter includes the following sections:

♦

Site preparation

♦

Cabinet requirements

♦

Rack requirements

♦

Unpacking the appliance

Site Preparation

Hillstone SG-6000-X7180 must be installed in indoor place. You should follow the
instructions in this section to ensure that your site is properly prepared for the device
installation.

Temperature/Humidity Specifications

Table 2-1 specifies the environmental temperature and relative humidity required for
the device.

Table 2-1: Temperature/Humidity Specifications

Description

Value

Temperature

Normal operation ensured in temperature range of 0

℃

to 40

℃

;

Non-operating storage temperature in package: -40

℃

to 70

℃

Relative humidity

Normal operation ensured in relative humidity range of 10% to

90%, non-condensing.

Cleanness Requirements

The installation site should not have explosive, electric conductive, magnetic
conductive or corrosive dusts.

Содержание SG-6000-X7180

































































Результаты поиска

Содержание SG-6000-X7180

Отзывы:

Похожие инструкции для SG-6000-X7180

Бренды по названию

Популярные бренды

Hillstone SG-6000-X7180, Справочник по аппаратуре

Результаты поиска

Содержание SG-6000-X7180

Отзывы:

Похожие инструкции для SG-6000-X7180

Бренды по названию

Популярные бренды