Hillrom Welch Allyn Connex ProBP 3400 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

Hillrom Welch Allyn Connex ProBP 3400 Скачать руководство пользователя страница 13

Overview

Purpose and scope

This service manual is a reference for periodic preventive maintenance and corrective service
procedures for the device. It is intended for use only by trained and qualified service personnel.

Corrective service is supported to the level of field-replaceable units. These include circuit-board
assemblies and some subassemblies, case parts, and other parts.

CAUTION

No component-level repair of circuit boards and subassemblies is

supported. Use only the repair procedures described in this manual.

WARNING

When performing a service procedure, follow the instructions exactly

as presented in this manual. Failure to do so could damage the device, invalidate
the product warranty, and lead to serious personal injury.

Find instructions for functional testing and performance verification in the Welch Allyn Service Tool
help files.

Service work not described in this manual must be performed by qualified service personnel at the
factory or at an authorized Welch Allyn service center.

For information about servicing any other product, see the service manual for that product.

Related documents

When using this manual, refer to the following:
•

Welch Allyn Connex ProBP 3400 Digital Blood Pressure Device Directions for Use

(part number

103701)

•

Welch Allyn Service Tool CD (part number 103521)

•

Welch Allyn Service Tool Installation and Configuration Guide

(part number 103820)

•

Welch Allyn website:

www.welchallyn.com

Technical support services

Welch Allyn offers the following technical support services:
•

Telephone support

•

Advance replacement equipment

•

Service agreements

•

Service training

9

«
...
11
12
13
14
15
...
»

Содержание Welch Allyn Connex ProBP 3400

































































Отзывы:

Нет отзывов