Hillrom Compella Скачать руководство пользователя страница 79

Страница: 79 / 116

Surface Features and Controls

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

10. If

Exit CLRT

is selected, the patient is centered, CLRT stops and the surface goes into Pressure

Redistribution mode. The Pressure Redistribution screen shows.

Deflate and Inflate the Side Bolsters and Foot Section

Automatically (using the Caregiver Width Adjust controls)

The side bolsters and foot section automatically adjust to the frame width
and/or length as long as the bed is plugged into AC power and the air supply
unit is correctly connected to the frame (see “Bed Width Adjustment” on
page 33).

Side Bolsters

•

The side bolsters will inflate anytime the frame
width extensions are all fully extended.

•

The side bolsters will deflate for 2 minutes
anytime some or all of the frame width
extensions are partially or fully retracted.

Foot Section

The foot section will automatically inflate or deflate
sufficiently to accommodate any adjustment to the foot extension of the frame.

Manually (using the Air Supply Unit)

The side bolsters and foot section can be operated manually

only

when the frame is disconnected from

AC power

the air supply unit loses communication with the frame.

Side Bolsters

To deflate the side bolsters, do as follows:

At the Pressure Redistribution screen, press

Mattress Adjust

Press

Deflate Sides

. The

Sides Deflating

screen shows.

NOTE:

During the Deflate Sides mode, you may use Seat
Deflate mode, Foot Deflate mode, Max Inflate
mode, or Transport Deflate mode as necessary.

If the side bolsters are deflated for 30 minutes,
an alarm sounds, and the

Warning: Sides

Deflated

screen shows:

Retract

Extend

Содержание Compella





















































































































Результаты поиска

Содержание Compella

Отзывы:

Бренды по названию

Популярные бренды

Hillrom Compella, Инструкция по эксплуатации

Результаты поиска

Содержание Compella

Отзывы:

Бренды по названию

Популярные бренды